Rectangular opposed blade volume control damper with external linkage

클린룸 공기 분배 시스템

반대쪽 블레이드 볼륨 제어 댐퍼

A rectangular multiblade damper whose adjacent linked blades rotate in opposite directions for stable duct volume control and compact shutoff.

True Opposed Blade Action
External Linkage
Low-Leakage Edge Seals
Manual or Motorized Drive

견적 요청 제품 찾아보기

상품 소개

The opposed blade volume control damper regulates air through rectangular cleanroom branches, equipment inlets and wall openings. Alternating aerofoil blades rotate toward and away from each other through an external linkage, dividing the throttling effect across the full face rather than concentrating it at one edge. A rigid channel frame keeps blade shafts aligned, while tip and side seals reduce closed-position leakage. The drive remains outside the airstream and can accept a manual quadrant, electric actuator or pneumatic operator.

주요 기능

Alternating blade rotation creates a more even downstream velocity profile during throttled operation.

External linkage keeps moving joints out of the primary air path and visible for inspection.

Formed aerofoil blades resist vibration and reduce pressure loss when fully open.

Side and blade-tip seals limit bypass when the damper is used for branch isolation.

고객 제품 관심사

A balancing damper must provide stable modulation without blade chatter, distorted downstream flow or excessive closed-position leakage.

Parallel blades push most throttled airflow toward one side of the downstream duct.Opposed blade motion divides the openings across the face and produces a more balanced discharge profile.

Large blades twist or chatter under high duct velocity.Double-skin aerofoil sections and intermediate shaft supports maintain blade rigidity across wider dampers.

Internal linkage cannot be inspected without opening contaminated ductwork.The drive arm, transverse link and blade connectors are mounted outside the casing.

Air continues leaking through a nominally closed branch.Compressible blade-tip and side seals close the remaining gaps between aerofoil blades and frame.

일반적인 응용 프로그램

Cleanroom branch duct balancingAir-handler inlet and discharge controlSupply and extract isolationPlenum pressure adjustmentProcess exhaust volume regulation

기술 매개변수

Representative material and dimensional ranges for a rectangular opposed blade control damper are listed below.

핵심 재료	Galvanized-steel or 304 stainless-steel channel frame with linked double-skin aerofoil blades
패널 두께	1.0–2.0 mm frame channels and double-skin blade sheets
유효 폭	200–2000 mm nominal single-section width
최대 길이	Up to 2000 mm single-section width, with subdivided assemblies for larger openings
강철 면면 두께	1.0–2.0 mm galvanized or stainless frame and blade material
코어 밀도	Approximately 7850 kg/m³ for galvanized-steel frame and blade construction
열전도도 (Thermal Conductivity)	Approximately 45–60 W/(m·K) for galvanized-steel frame and blade construction
표면 마무리	Mill-galvanized, white powder-coated or brushed stainless-steel finish
접합 유형	Flanged rectangular frame with external opposed-action linkage and sealed blade edges
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

Galvanized steel or 304 stainless steelManual quadrant, electric actuator or pneumatic driveLow-leakage blade and jamb sealsFlanged, drilled or corner-hole duct frame

Planning a Opposed Blade Volume Control Damper specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.