İngilizce
Almanca
Arapça
Fransızca
Endonezya dilinde
Japonca
Korece
Malay dilinde
Portekizce
Rusça
İspanyolca
Taylandca
TürkçeCurrent
Vietnamca
Temiz Oda Ekipmanları Yedek Parçaları
Isıtma Coil
A shallow finned-tube hot-water coil for restoring sensible preheat or reheat duty in a matched cleanroom air-handling unit.
- One- or Two-Row Heating Core
- Copper Water Circuit
- Low Airside Depth
- Service-Side Threaded Unions
Ürün tanıtımı
The heating coil is a compact hydronic heat exchanger installed upstream or downstream of other AHU treatment stages to raise dry-bulb air temperature. Hot water flows through parallel copper tubes mechanically expanded into aluminum plate fins, and a shallow galvanized casing supports the assembly at the air-handler opening. Heating duty commonly requires fewer tube rows than a chilled-water cooling section, reducing core depth and air resistance where the selected entering-water temperature permits. Replacement selection must match the original face dimensions, tube-row count, circuit arrangement, connection orientation and required sensible heating performance.
Ana Özellikler
Mechanically expanded copper tubes maintain direct thermal contact with the continuous aluminum fin surface.
A rigid galvanized frame and corner mounting ears provide defined support at the AHU or duct opening.
The accessible copper header groups the hot-water supply and return connections on one service side.
Müşteri Ürün Sorunları
A replacement heating coil must provide the required sensible capacity without excessive water resistance, air pressure drop or freeze exposure.
A deeper or more densely finned core consumes fan pressure that was not available in the original AHU.Tube rows and fin spacing are selected around the heating load, face velocity and allowable airside resistance.
Incorrect supply and return positions make the existing pipework difficult to reconnect and service.Header side, union orientation, center spacing and thread size are matched to the removed coil or verified equipment drawing.
Poor circuit distribution creates uneven leaving-air temperature across the coil face.Tube passes and header layout are arranged for balanced water flow across the selected face dimensions.
Stagnant water can freeze when cold outdoor air reaches an inactive preheat coil.The coil selection can incorporate suitable circuit velocity, vent and drain provisions, and compatible water-glycol service where required by the operating conditions.
Tipik uygulamalar
Cleanroom AHU preheat sectionsSupply-air reheat stagesMake-up air tempering unitsReplacement hot-water coil modules
Teknik parametreler
The ranges below describe typical material and envelope choices for compact water-fed air reheating sections.
| Temel malzemeler | Seamless copper water tubes mechanically expanded into continuous aluminum plate fins |
|---|---|
| Panel kalınlığı | 45-180 mm nominal coil depth for common one- or two-row heating selections |
| Effective Width (Etkili Genişlik) | 300-2200 mm nominal finned face width |
| Maksimum uzunluk | Up to 2800 mm overall casing length for common AHU replacement sections |
| Çelik yüz yüze kalınlığı | 1.0-1.6 mm galvanized-steel casing and mounting-ear thickness |
| Core Density (Çekirdek Yoğunluğu) | Approximately 8900-8960 kg/m³ for copper tube and header components |
| Termal İletkenlik | Approximately 380-400 W/(m·K) for copper heat-transfer tubes |
| Yüzey bitirme | Natural galvanized-silver casing and aluminum fins with copper header and brass female threaded unions |
| Ortak tip | Mechanically expanded tube-to-fin bond with brazed copper circuits and female threaded header connections |
| Customization (Özelleşme) | Kullanılan uygulama ve çalışma ortamına göre kullanılabilir. |
Mevcut Seçenekler
One- or two-row constructionCustom face size and fin spacingLeft- or right-hand header arrangementOptional vent, drain and protective fin coating
Planning a Heating Coil specification?
Bize boyutlarınızı, montaj koşullarınızı, performans hedeflerinizi ve gerekli yüzey kaplamalarınızı gönderin.
