Three-quarter view of an upright AHU hot-water heating coil with left copper header

クリーンルーム機器のスペアパーツ

暖房コイル

A shallow finned-tube hot-water coil for restoring sensible preheat or reheat duty in a matched cleanroom air-handling unit.

One- or Two-Row Heating Core
Copper Water Circuit
Low Airside Depth
Service-Side Threaded Unions

見積もりリクエスト製品案内

商品紹介

The heating coil is a compact hydronic heat exchanger installed upstream or downstream of other AHU treatment stages to raise dry-bulb air temperature. Hot water flows through parallel copper tubes mechanically expanded into aluminum plate fins, and a shallow galvanized casing supports the assembly at the air-handler opening. Heating duty commonly requires fewer tube rows than a chilled-water cooling section, reducing core depth and air resistance where the selected entering-water temperature permits. Replacement selection must match the original face dimensions, tube-row count, circuit arrangement, connection orientation and required sensible heating performance.

主要な特徴

A one- or two-row tube arrangement provides a shallow heating section for preheat and reheat duties.

Mechanically expanded copper tubes maintain direct thermal contact with the continuous aluminum fin surface.

A rigid galvanized frame and corner mounting ears provide defined support at the AHU or duct opening.

The accessible copper header groups the hot-water supply and return connections on one service side.

お客様の製品に関する懸念事項

A replacement heating coil must provide the required sensible capacity without excessive water resistance, air pressure drop or freeze exposure.

A deeper or more densely finned core consumes fan pressure that was not available in the original AHU.Tube rows and fin spacing are selected around the heating load, face velocity and allowable airside resistance.

Incorrect supply and return positions make the existing pipework difficult to reconnect and service.Header side, union orientation, center spacing and thread size are matched to the removed coil or verified equipment drawing.

Poor circuit distribution creates uneven leaving-air temperature across the coil face.Tube passes and header layout are arranged for balanced water flow across the selected face dimensions.

Stagnant water can freeze when cold outdoor air reaches an inactive preheat coil.The coil selection can incorporate suitable circuit velocity, vent and drain provisions, and compatible water-glycol service where required by the operating conditions.

典型的な用途

Cleanroom AHU preheat sectionsSupply-air reheat stagesMake-up air tempering unitsReplacement hot-water coil modules

技術的なパラメータ

The ranges below describe typical material and envelope choices for compact water-fed air reheating sections.

コア材料	Seamless copper water tubes mechanically expanded into continuous aluminum plate fins
パネルの厚さ	45-180 mm nominal coil depth for common one- or two-row heating selections
有効幅	300-2200 mm nominal finned face width
最大長さ	Up to 2800 mm overall casing length for common AHU replacement sections
鋼鉄の厚さを直面する	1.0-1.6 mm galvanized-steel casing and mounting-ear thickness
コア密度	Approximately 8900-8960 kg/m³ for copper tube and header components
熱伝導率	Approximately 380-400 W/(m·K) for copper heat-transfer tubes
表面仕上げ	Natural galvanized-silver casing and aluminum fins with copper header and brass female threaded unions
ジョイントタイプ	Mechanically expanded tube-to-fin bond with brazed copper circuits and female threaded header connections
カスタマイズ	意図したアプリケーションと動作環境に基づいて利用できます。

利用可能なオプション

One- or two-row constructionCustom face size and fin spacingLeft- or right-hand header arrangementOptional vent, drain and protective fin coating

Planning a Heating Coil specification?

寸法、設置条件、性能目標、必要な表面仕上げをお送りください。

チームに相談する