English
Немецкий
Арабский язык
Французский
Индонезийский
Японский язык
Корейский
Японский
Португальский
Русский языкТекущий
Испанский язык
Тайский
Турецкий
Вьетнамский язык
Запчасти для оборудования для чистых помещений
УФ лампа трубка
A double-ended clear-quartz UV-C discharge tube for restoring the germicidal source inside compatible enclosed cleanroom and air-treatment equipment.
- Clear Fused-Quartz Envelope
- Double-Ended G13 Bi-Pin Caps
- Low-Pressure UV-C Discharge
- Single-Tube Service Replacement
Введение продукции
This UV lamp tube is a replaceable low-pressure mercury discharge source for compatible enclosed air, surface and equipment-disinfection systems. One transparent T8 quartz envelope carries an electrode assembly at each end, while two white ceramic G13 caps provide four fixed contact pins for mechanical seating and electrical connection. The lamp contains no holder, reflector, ballast or enclosure, so tube length, diameter, wattage, operating current and control-gear type are matched to the existing unit before installation. Its germicidal output is invisible during normal operation; the replacement is therefore intended only for equipment that prevents unshielded personnel exposure and safely controls lamp operation.
Основные характеристики
Two medium bi-pin end caps provide a defined four-contact interface that supports quick tube removal without replacing the permanent fixture body.
Separate electrode structures at the two ends sustain the low-pressure discharge along one continuous tube rather than using LEDs or a visible-light phosphor coating.
A single bare-lamp format allows maintenance teams to replace only the spent radiation source when the existing holders, ballast and protective enclosure remain serviceable.
Обеспокоенность клиентов продуктами
A tube that appears mechanically similar can still be incompatible with the installed holders or ballast; safe replacement requires the physical, electrical and shielding conditions to match as one system.
A lamp with the wrong overall length or pin spacing will not seat squarely in the existing G13 holders.Base-face length, overall pin-tip length, tube diameter and two-pin geometry are checked against the removed tube before selection.
Incorrect wattage, operating current or ballast type can prevent stable ignition and accelerate electrode wear.The replacement electrical rating is matched to the installed magnetic or electronic control gear rather than selected by appearance alone.
Quartz contamination and fingerprints can create local hot spots or reduce useful transmission after handling.The tube is handled by its ceramic caps or with clean gloves and the quartz surface is cleaned using a compatible lint-free method before operation.
An exposed operating UV-C source can injure eyes and skin even though the radiation is not visibly bright.The lamp is operated only inside a closed shielded unit with functional covers, door interlocks and power isolation for servicing.
Типичные приложения
Enclosed cleanroom air-disinfection modulesUV-C sections in air-handling and duct equipmentCompatible transfer-chamber irradiation systemsShielded laboratory and process-equipment sterilization units
Технические параметры
The ranges below describe common double-ended T8/G13 low-pressure UV-C replacement lamps; the exact electrical rating and tube length are selected for the existing disinfection equipment.
| Основной материал | Clear fused-quartz low-pressure mercury and rare-gas discharge envelope with internal electrodes and white ceramic G13 end caps |
|---|---|
| Толщина панели | 0.8-1.5 mm representative quartz tube-wall thickness |
| эффективная ширина | 26-28 mm nominal T8 tube outside diameter |
| Максимальная длина | Up to 1214 mm overall pin-tip length for representative long T8 versions |
| Толщина линий стали | 0 mm steel facing; the radiation envelope is clear quartz glass |
| Плотность ядра | Approximately 2200-2203 kg/m³ for representative fused quartz |
| Теплопроводимость | Approximately 1.38 W/(m·K) for representative fused quartz at room temperature |
| Поверхностная отделка | Clear polished quartz tube, plain white ceramic caps and neutral nickel-colored contact pins |
| Объединенный тип | Double-ended G13 medium bi-pin connection with one ceramic cap and two fixed parallel pins at each end |
| Customization | Доступно в зависимости от предполагаемого применения и операционной среды. |
Доступные варианты
Tube length and wattage matched to the existing equipmentStandard-output or high-output electrical configurationOzone-suppressing or ozone-producing quartz transmission optionCompatible magnetic-ballast or electronic-ballast version
Planning a UV Lamp Tube specification?
Отправьте нам ваши габариты, условия монтажа, целевые показатели производительности и требуемую отделку поверхности.
