Inglés
Alemán
El árabe
Francés
Idioma indonesio
El japonés
Coreano
El malayo
El portugués
El ruso
EspañolCurrent
Tailandés
El turco
El vietnamita
Equipos de sala limpia piezas de repuesto
Lámpara UV Tube
A double-ended clear-quartz UV-C discharge tube for restoring the germicidal source inside compatible enclosed cleanroom and air-treatment equipment.
- Clear Fused-Quartz Envelope
- Double-Ended G13 Bi-Pin Caps
- Low-Pressure UV-C Discharge
- Single-Tube Service Replacement
Introducción del producto
This UV lamp tube is a replaceable low-pressure mercury discharge source for compatible enclosed air, surface and equipment-disinfection systems. One transparent T8 quartz envelope carries an electrode assembly at each end, while two white ceramic G13 caps provide four fixed contact pins for mechanical seating and electrical connection. The lamp contains no holder, reflector, ballast or enclosure, so tube length, diameter, wattage, operating current and control-gear type are matched to the existing unit before installation. Its germicidal output is invisible during normal operation; the replacement is therefore intended only for equipment that prevents unshielded personnel exposure and safely controls lamp operation.
Características clave
Two medium bi-pin end caps provide a defined four-contact interface that supports quick tube removal without replacing the permanent fixture body.
Separate electrode structures at the two ends sustain the low-pressure discharge along one continuous tube rather than using LEDs or a visible-light phosphor coating.
A single bare-lamp format allows maintenance teams to replace only the spent radiation source when the existing holders, ballast and protective enclosure remain serviceable.
Preocupaciones del producto del cliente
A tube that appears mechanically similar can still be incompatible with the installed holders or ballast; safe replacement requires the physical, electrical and shielding conditions to match as one system.
A lamp with the wrong overall length or pin spacing will not seat squarely in the existing G13 holders.Base-face length, overall pin-tip length, tube diameter and two-pin geometry are checked against the removed tube before selection.
Incorrect wattage, operating current or ballast type can prevent stable ignition and accelerate electrode wear.The replacement electrical rating is matched to the installed magnetic or electronic control gear rather than selected by appearance alone.
Quartz contamination and fingerprints can create local hot spots or reduce useful transmission after handling.The tube is handled by its ceramic caps or with clean gloves and the quartz surface is cleaned using a compatible lint-free method before operation.
An exposed operating UV-C source can injure eyes and skin even though the radiation is not visibly bright.The lamp is operated only inside a closed shielded unit with functional covers, door interlocks and power isolation for servicing.
Aplicaciones típicas
Enclosed cleanroom air-disinfection modulesUV-C sections in air-handling and duct equipmentCompatible transfer-chamber irradiation systemsShielded laboratory and process-equipment sterilization units
Parámetros técnicos
The ranges below describe common double-ended T8/G13 low-pressure UV-C replacement lamps; the exact electrical rating and tube length are selected for the existing disinfection equipment.
| Materiales Core | Clear fused-quartz low-pressure mercury and rare-gas discharge envelope with internal electrodes and white ceramic G13 end caps |
|---|---|
| Panel de espesor | 0.8-1.5 mm representative quartz tube-wall thickness |
| Ancho efectivo | 26-28 mm nominal T8 tube outside diameter |
| Longitud máxima | Up to 1214 mm overall pin-tip length for representative long T8 versions |
| Acero frente a espesor | 0 mm steel facing; the radiation envelope is clear quartz glass |
| Densidad Core | Approximately 2200-2203 kg/m³ for representative fused quartz |
| Conductividad térmica | Approximately 1.38 W/(m·K) for representative fused quartz at room temperature |
| Superficie acabada | Clear polished quartz tube, plain white ceramic caps and neutral nickel-colored contact pins |
| Tipo conjunto | Double-ended G13 medium bi-pin connection with one ceramic cap and two fixed parallel pins at each end |
| Customization | Disponible según la aplicación prevista y el entorno operativo. |
Opciones disponibles
Tube length and wattage matched to the existing equipmentStandard-output or high-output electrical configurationOzone-suppressing or ozone-producing quartz transmission optionCompatible magnetic-ballast or electronic-ballast version
Planning a UV Lamp Tube specification?
Envíenos sus dimensiones, condiciones de instalación, objetivos de rendimiento y acabado superficial requerido.
