Front-left three-quarter view of one clear quartz G13 UV-C replacement lamp tube with four pins

클린룸 장비 예비 부품

UV 램프 튜브

A double-ended clear-quartz UV-C discharge tube for restoring the germicidal source inside compatible enclosed cleanroom and air-treatment equipment.

Clear Fused-Quartz Envelope
Double-Ended G13 Bi-Pin Caps
Low-Pressure UV-C Discharge
Single-Tube Service Replacement

견적 요청 제품 찾아보기

상품 소개

This UV lamp tube is a replaceable low-pressure mercury discharge source for compatible enclosed air, surface and equipment-disinfection systems. One transparent T8 quartz envelope carries an electrode assembly at each end, while two white ceramic G13 caps provide four fixed contact pins for mechanical seating and electrical connection. The lamp contains no holder, reflector, ballast or enclosure, so tube length, diameter, wattage, operating current and control-gear type are matched to the existing unit before installation. Its germicidal output is invisible during normal operation; the replacement is therefore intended only for equipment that prevents unshielded personnel exposure and safely controls lamp operation.

주요 기능

The clear fused-quartz envelope transmits the intended short-wave output while retaining the familiar straight T8 geometry used by many professional disinfection systems.

Two medium bi-pin end caps provide a defined four-contact interface that supports quick tube removal without replacing the permanent fixture body.

Separate electrode structures at the two ends sustain the low-pressure discharge along one continuous tube rather than using LEDs or a visible-light phosphor coating.

A single bare-lamp format allows maintenance teams to replace only the spent radiation source when the existing holders, ballast and protective enclosure remain serviceable.

고객 제품 관심사

A tube that appears mechanically similar can still be incompatible with the installed holders or ballast; safe replacement requires the physical, electrical and shielding conditions to match as one system.

A lamp with the wrong overall length or pin spacing will not seat squarely in the existing G13 holders.Base-face length, overall pin-tip length, tube diameter and two-pin geometry are checked against the removed tube before selection.

Incorrect wattage, operating current or ballast type can prevent stable ignition and accelerate electrode wear.The replacement electrical rating is matched to the installed magnetic or electronic control gear rather than selected by appearance alone.

Quartz contamination and fingerprints can create local hot spots or reduce useful transmission after handling.The tube is handled by its ceramic caps or with clean gloves and the quartz surface is cleaned using a compatible lint-free method before operation.

An exposed operating UV-C source can injure eyes and skin even though the radiation is not visibly bright.The lamp is operated only inside a closed shielded unit with functional covers, door interlocks and power isolation for servicing.

일반적인 응용 프로그램

Enclosed cleanroom air-disinfection modulesUV-C sections in air-handling and duct equipmentCompatible transfer-chamber irradiation systemsShielded laboratory and process-equipment sterilization units

기술 매개변수

The ranges below describe common double-ended T8/G13 low-pressure UV-C replacement lamps; the exact electrical rating and tube length are selected for the existing disinfection equipment.

핵심 재료	Clear fused-quartz low-pressure mercury and rare-gas discharge envelope with internal electrodes and white ceramic G13 end caps
패널 두께	0.8-1.5 mm representative quartz tube-wall thickness
유효 폭	26-28 mm nominal T8 tube outside diameter
최대 길이	Up to 1214 mm overall pin-tip length for representative long T8 versions
강철 면면 두께	0 mm steel facing; the radiation envelope is clear quartz glass
코어 밀도	Approximately 2200-2203 kg/m³ for representative fused quartz
열전도도 (Thermal Conductivity)	Approximately 1.38 W/(m·K) for representative fused quartz at room temperature
표면 마무리	Clear polished quartz tube, plain white ceramic caps and neutral nickel-colored contact pins
접합 유형	Double-ended G13 medium bi-pin connection with one ceramic cap and two fixed parallel pins at each end
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

Tube length and wattage matched to the existing equipmentStandard-output or high-output electrical configurationOzone-suppressing or ozone-producing quartz transmission optionCompatible magnetic-ballast or electronic-ballast version

Planning a UV Lamp Tube specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.