English
Немецкий
Арабский язык
Французский
Индонезийский
Японский язык
Корейский
Японский
Португальский
Русский языкТекущий
Испанский язык
Тайский
Турецкий
Вьетнамский язык
Воздушные фильтры и химическая фильтрация
Выхлопный фильтр HEPA
A robust deep-box HEPA filter configured for cleanroom and laboratory exhaust systems, including front-access and bag-in/bag-out containment housings.
- Containment Exhaust Duty
- Deep Reinforced Pack
- Two-Sided Face Protection
- Housing-Compatible Gasket
Введение продукции
The exhaust HEPA filter uses a deep glass-microfibre pack housed in a rigid galvanized-steel or stainless-steel box. Media separators and protective faceguards on both sides help the filter withstand turbulent extract air, maintenance handling and the controlled change procedure used in containment housings. Continuous polyurethane potting seals the pack edge, and a carefully positioned closed-cell gasket mates with front-access, side-access or bag-in/bag-out clamping frames. Optional high-capacity and incinerable configurations address different exhaust loading and disposal strategies.
Основные характеристики
Upstream and downstream faceguards shield the media from debris and accidental contact in exhaust service.
Deep-pleat or high-area mini-pleat configurations accommodate different airflow and dust-loading requirements.
Gasket placement can be matched to the knife-edge or sealing flange direction of the exhaust housing.
Обеспокоенность клиентов продуктами
Exhaust filters capture contaminants before discharge and must remain intact through loading, isolation and maintenance handling.
An exposed media face is damaged by debris entering the exhaust branch.Dual rigid faceguards protect both sides of the pack while preserving the open flow area.
A loaded filter deforms as it is pulled into a change-out bag.A reinforced metal box keeps the filter square and supports the media pack during controlled removal.
The gasket is installed on the wrong face for the containment housing clamp.Upstream, downstream or double-gasket arrangements are selected to match the housing seal plane.
Exhaust loading causes an unexpectedly rapid pressure rise.Deep-pleat or V-bank media area is selected according to extract airflow and anticipated aerosol burden.
Типичные приложения
Laboratory containment exhaustPharmaceutical process extract systemsHospital isolation-room exhaustCytotoxic preparation facilitiesBag-in/bag-out filter housings
Технические параметры
Typical construction ranges for a cleanroom exhaust HEPA filter are shown below.
| Основной материал | Water-resistant glass-microfibre HEPA media in deep-pleat or high-area mini-pleat construction |
|---|---|
| Толщина панели | 150–292 mm overall filter depth |
| эффективная ширина | 305–610 mm nominal face width |
| Максимальная длина | Up to 762 mm nominal face height |
| Толщина линий стали | 0.8–1.2 mm galvanized-steel or stainless-steel box frame |
| Плотность ядра | Approximately 40–65 kg/m³ equivalent packed-media density |
| Теплопроводимость | Approximately 0.035–0.045 W/(m·K) for the dry glass-microfibre pack |
| Поверхностная отделка | Mill-galvanized or brushed stainless-steel frame with two protective faceguards |
| Объединенный тип | Upstream, downstream or double closed-cell gasket for containment-housing clamping |
| Customization | Доступно в зависимости от предполагаемого применения и операционной среды. |
Доступные варианты
H13 or H14 efficiencySeparator-style, mini-pleat or V-bank media packGalvanized or stainless-steel constructionSingle gasket, double gasket or gel-seal interface
Planning a Exhaust HEPA Filter specification?
Отправьте нам ваши габариты, условия монтажа, целевые показатели производительности и требуемую отделку поверхности.
