Three-quarter view of reinforced exhaust HEPA filter with dual faceguards

공기 필터 및 화학 여과

배기 HEPA 필터

A robust deep-box HEPA filter configured for cleanroom and laboratory exhaust systems, including front-access and bag-in/bag-out containment housings.

Containment Exhaust Duty
Deep Reinforced Pack
Two-Sided Face Protection
Housing-Compatible Gasket

견적 요청 제품 찾아보기

상품 소개

The exhaust HEPA filter uses a deep glass-microfibre pack housed in a rigid galvanized-steel or stainless-steel box. Media separators and protective faceguards on both sides help the filter withstand turbulent extract air, maintenance handling and the controlled change procedure used in containment housings. Continuous polyurethane potting seals the pack edge, and a carefully positioned closed-cell gasket mates with front-access, side-access or bag-in/bag-out clamping frames. Optional high-capacity and incinerable configurations address different exhaust loading and disposal strategies.

주요 기능

A reinforced metal box protects the filtration pack during removal through containment bags or glove-access housings.

Upstream and downstream faceguards shield the media from debris and accidental contact in exhaust service.

Deep-pleat or high-area mini-pleat configurations accommodate different airflow and dust-loading requirements.

Gasket placement can be matched to the knife-edge or sealing flange direction of the exhaust housing.

고객 제품 관심사

Exhaust filters capture contaminants before discharge and must remain intact through loading, isolation and maintenance handling.

An exposed media face is damaged by debris entering the exhaust branch.Dual rigid faceguards protect both sides of the pack while preserving the open flow area.

A loaded filter deforms as it is pulled into a change-out bag.A reinforced metal box keeps the filter square and supports the media pack during controlled removal.

The gasket is installed on the wrong face for the containment housing clamp.Upstream, downstream or double-gasket arrangements are selected to match the housing seal plane.

Exhaust loading causes an unexpectedly rapid pressure rise.Deep-pleat or V-bank media area is selected according to extract airflow and anticipated aerosol burden.

일반적인 응용 프로그램

Laboratory containment exhaustPharmaceutical process extract systemsHospital isolation-room exhaustCytotoxic preparation facilitiesBag-in/bag-out filter housings

기술 매개변수

Typical construction ranges for a cleanroom exhaust HEPA filter are shown below.

핵심 재료	Water-resistant glass-microfibre HEPA media in deep-pleat or high-area mini-pleat construction
패널 두께	150–292 mm overall filter depth
유효 폭	305 - 610 mm 공칭 면 너비
최대 길이	Up to 762 mm nominal face height
강철 면면 두께	0.8–1.2 mm galvanized-steel or stainless-steel box frame
코어 밀도	Approximately 40–65 kg/m³ equivalent packed-media density
열전도도 (Thermal Conductivity)	Approximately 0.035–0.045 W/(m·K) for the dry glass-microfibre pack
표면 마무리	Mill-galvanized or brushed stainless-steel frame with two protective faceguards
접합 유형	Upstream, downstream or double closed-cell gasket for containment-housing clamping
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

H13 or H14 efficiencySeparator-style, mini-pleat or V-bank media packGalvanized or stainless-steel constructionSingle gasket, double gasket or gel-seal interface

Planning a Exhaust HEPA Filter specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.