Inglês
Alemão
Língua árabe
Francês
Língua indonésia
Japonês
Coreano
Língua malaia
Portuguêsatual
Língua russa
Espanhol
Tailandês
Língua turca
Vietnã
Acessórios de instalação de sala limpa
Guardas de canto de aço inoxidável
A one-piece 304 stainless steel angle with two equal 51 mm wings, a hygienic No. 4 brushed finish and hole-free adhesive mounting for exposed cleanroom corners.
- Type 304 Stainless Steel
- Equal 51 mm Wings
- Hole-Free Adhesive Mount
- No. 4 Brushed Finish
Introdução do produto
This surface-mounted corner guard is formed from a single sheet of Type 304 stainless steel into a consistent 90-degree profile. Two equal-width wings cover both faces of an outside wall corner, while a small rounded bend removes the sharp visual line associated with a square folded edge. The cement-on configuration has no exposed fixing holes, and its vertical No. 4 grain produces a durable satin surface suited to frequent wiping in controlled interiors.
Características-chave
Equal 51 mm wings provide balanced coverage where carts, bins or movable equipment approach from either corridor direction.
A 1.5 mm nominal stainless sheet resists local denting while retaining a low-profile surface-mounted form.
Hole-free adhesive attachment leaves the exposed face uninterrupted by screw heads or countersunk recesses.
The directional No. 4 satin grain controls glare and supports straightforward wipe-down of the visible metal surfaces.
Preocupações do produto do cliente
Unprotected outside corners concentrate incidental impact on a narrow line, where repeated traffic can chip finishes and create difficult-to-clean damage.
A cart wheel or bin can repeatedly strike the same projecting wall edge and deform the local panel finish.Two equal stainless wings spread contact over both adjoining faces instead of leaving the corner line exposed.
Visible screw heads add recesses that interrupt routine cleaning along a controlled-area corridor.The adhesive-mounted configuration presents continuous metal faces with no predrilled fixing holes.
A thin decorative trim may lack the width needed to intercept mobile equipment before it reaches the wall surface.Each 51 mm wing provides practical coverage beyond the 90-degree bend while preserving a compact projection.
Highly reflective sheet metal can show fingerprints and create distracting glare under bright cleanroom lighting.A controlled No. 4 directional satin finish softens reflections and gives wiping a consistent grain direction.
Aplicações típicas
Cleanroom corridor outside cornersPharmaceutical processing circulation routesLaboratory and medical-device production areasMaterial transfer and equipment staging zonesHygienic service corridors exposed to trolley traffic
Parâmetros técnicos
Typical values for the selected adhesive-mounted 304 stainless steel corner-guard configuration are listed below.
| Material principal | One-piece Type 304 austenitic stainless steel sheet |
|---|---|
| Painel de espessura | 1.5 mm nominal formed-sheet thickness |
| Largura efetiva | 51 mm per wing, with two equal-width wings |
| Comprimento máximo | Up to 2438 mm for a standard continuous guard |
| Aço enfrentando espessura | 1.5 mm Type 304 stainless steel, approximately 16 gauge |
| Densidade Core | Approximately 7900 kg/m³ for Type 304 stainless steel |
| Condutividade térmica | Approximately 15 W/(m·K) at 20°C |
| Superfície acabado | No. 4 directional brushed satin stainless steel with neutral silver midtones |
| Tipo conjunto | Single-piece 90-degree bend with two equal legs and hole-free heavy-duty adhesive surface mounting |
| Customização | Disponível com base na aplicação pretendida e no ambiente operacional. |
Opções disponíveis
Alternative 38 mm or 89 mm equal-wing sizesFactory-cut lengths for the protected wall heightOptional predrilled screw-mount configurationAlternative bend angles for non-square outside cornersType 316 stainless steel for more demanding chemical exposure
Planning a Stainless Steel Corner Guard specification?
Envie-nos as suas dimensões, condições de instalação, metas de desempenho e acabamento de superfície necessário.
