Three-quarter view of an adhesive-mounted 304 stainless steel corner guard with equal 51 mm wings

클린룸 설치 액세서리

스테인레스 스틸 코너 가드

A one-piece 304 stainless steel angle with two equal 51 mm wings, a hygienic No. 4 brushed finish and hole-free adhesive mounting for exposed cleanroom corners.

Type 304 Stainless Steel
Equal 51 mm Wings
Hole-Free Adhesive Mount
No. 4 Brushed Finish

견적 요청 제품 찾아보기

상품 소개

This surface-mounted corner guard is formed from a single sheet of Type 304 stainless steel into a consistent 90-degree profile. Two equal-width wings cover both faces of an outside wall corner, while a small rounded bend removes the sharp visual line associated with a square folded edge. The cement-on configuration has no exposed fixing holes, and its vertical No. 4 grain produces a durable satin surface suited to frequent wiping in controlled interiors.

주요 기능

The 90-degree one-piece profile shields both sides of a vulnerable outside corner without a separate carrier or cover.

Equal 51 mm wings provide balanced coverage where carts, bins or movable equipment approach from either corridor direction.

A 1.5 mm nominal stainless sheet resists local denting while retaining a low-profile surface-mounted form.

Hole-free adhesive attachment leaves the exposed face uninterrupted by screw heads or countersunk recesses.

The directional No. 4 satin grain controls glare and supports straightforward wipe-down of the visible metal surfaces.

고객 제품 관심사

Unprotected outside corners concentrate incidental impact on a narrow line, where repeated traffic can chip finishes and create difficult-to-clean damage.

A cart wheel or bin can repeatedly strike the same projecting wall edge and deform the local panel finish.Two equal stainless wings spread contact over both adjoining faces instead of leaving the corner line exposed.

Visible screw heads add recesses that interrupt routine cleaning along a controlled-area corridor.The adhesive-mounted configuration presents continuous metal faces with no predrilled fixing holes.

A thin decorative trim may lack the width needed to intercept mobile equipment before it reaches the wall surface.Each 51 mm wing provides practical coverage beyond the 90-degree bend while preserving a compact projection.

Highly reflective sheet metal can show fingerprints and create distracting glare under bright cleanroom lighting.A controlled No. 4 directional satin finish softens reflections and gives wiping a consistent grain direction.

일반적인 응용 프로그램

Cleanroom corridor outside cornersPharmaceutical processing circulation routesLaboratory and medical-device production areasMaterial transfer and equipment staging zonesHygienic service corridors exposed to trolley traffic

기술 매개변수

Typical values for the selected adhesive-mounted 304 stainless steel corner-guard configuration are listed below.

핵심 재료	One-piece Type 304 austenitic stainless steel sheet
패널 두께	1.5 mm nominal formed-sheet thickness
유효 폭	51 mm per wing, with two equal-width wings
최대 길이	Up to 2438 mm for a standard continuous guard
강철 면면 두께	1.5 mm Type 304 stainless steel, approximately 16 gauge
코어 밀도	Approximately 7900 kg/m³ for Type 304 stainless steel
열전도도 (Thermal Conductivity)	Approximately 15 W/(m·K) at 20°C
표면 마무리	No. 4 directional brushed satin stainless steel with neutral silver midtones
접합 유형	Single-piece 90-degree bend with two equal legs and hole-free heavy-duty adhesive surface mounting
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

Alternative 38 mm or 89 mm equal-wing sizesFactory-cut lengths for the protected wall heightOptional predrilled screw-mount configurationAlternative bend angles for non-square outside cornersType 316 stainless steel for more demanding chemical exposure

Planning a Stainless Steel Corner Guard specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.