Three-quarter view of an adhesive-mounted 304 stainless steel corner guard with equal 51 mm wings

Аксессуары для установки в чистых помещениях

Нержавеющая сталь Corner Guard

A one-piece 304 stainless steel angle with two equal 51 mm wings, a hygienic No. 4 brushed finish and hole-free adhesive mounting for exposed cleanroom corners.

Type 304 Stainless Steel
Equal 51 mm Wings
Hole-Free Adhesive Mount
No. 4 Brushed Finish

Запрос котировки Просмотреть продукты

Введение продукции

This surface-mounted corner guard is formed from a single sheet of Type 304 stainless steel into a consistent 90-degree profile. Two equal-width wings cover both faces of an outside wall corner, while a small rounded bend removes the sharp visual line associated with a square folded edge. The cement-on configuration has no exposed fixing holes, and its vertical No. 4 grain produces a durable satin surface suited to frequent wiping in controlled interiors.

Основные характеристики

The 90-degree one-piece profile shields both sides of a vulnerable outside corner without a separate carrier or cover.

Equal 51 mm wings provide balanced coverage where carts, bins or movable equipment approach from either corridor direction.

A 1.5 mm nominal stainless sheet resists local denting while retaining a low-profile surface-mounted form.

Hole-free adhesive attachment leaves the exposed face uninterrupted by screw heads or countersunk recesses.

The directional No. 4 satin grain controls glare and supports straightforward wipe-down of the visible metal surfaces.

Обеспокоенность клиентов продуктами

Unprotected outside corners concentrate incidental impact on a narrow line, where repeated traffic can chip finishes and create difficult-to-clean damage.

A cart wheel or bin can repeatedly strike the same projecting wall edge and deform the local panel finish.Two equal stainless wings spread contact over both adjoining faces instead of leaving the corner line exposed.

Visible screw heads add recesses that interrupt routine cleaning along a controlled-area corridor.The adhesive-mounted configuration presents continuous metal faces with no predrilled fixing holes.

A thin decorative trim may lack the width needed to intercept mobile equipment before it reaches the wall surface.Each 51 mm wing provides practical coverage beyond the 90-degree bend while preserving a compact projection.

Highly reflective sheet metal can show fingerprints and create distracting glare under bright cleanroom lighting.A controlled No. 4 directional satin finish softens reflections and gives wiping a consistent grain direction.

Типичные приложения

Cleanroom corridor outside cornersPharmaceutical processing circulation routesLaboratory and medical-device production areasMaterial transfer and equipment staging zonesHygienic service corridors exposed to trolley traffic

Технические параметры

Typical values for the selected adhesive-mounted 304 stainless steel corner-guard configuration are listed below.

Основной материал	One-piece Type 304 austenitic stainless steel sheet
Толщина панели	1.5 mm nominal formed-sheet thickness
эффективная ширина	51 mm per wing, with two equal-width wings
Максимальная длина	Up to 2438 mm for a standard continuous guard
Толщина линий стали	1.5 mm Type 304 stainless steel, approximately 16 gauge
Плотность ядра	Approximately 7900 kg/m³ for Type 304 stainless steel
Теплопроводимость	Approximately 15 W/(m·K) at 20°C
Поверхностная отделка	No. 4 directional brushed satin stainless steel with neutral silver midtones
Объединенный тип	Single-piece 90-degree bend with two equal legs and hole-free heavy-duty adhesive surface mounting
Customization	Доступно в зависимости от предполагаемого применения и операционной среды.

Доступные варианты

Alternative 38 mm or 89 mm equal-wing sizesFactory-cut lengths for the protected wall heightOptional predrilled screw-mount configurationAlternative bend angles for non-square outside cornersType 316 stainless steel for more demanding chemical exposure

Planning a Stainless Steel Corner Guard specification?

Отправьте нам ваши габариты, условия монтажа, целевые показатели производительности и требуемую отделку поверхности.

Поговорите с нашей командой