Large dry-room dehumidification system with dual desiccant sections and blue access doors

Equipamento de manuseio de ar e HVAC para sala limpa

Sistema de desumidificação de sala seca

An integrated high-recirculation air-treatment system that controls the complete moisture balance of a production dry room, including infiltration, occupants and process exhaust replacement.

Room-Wide Moisture Balance
High Recirculation Airflow
Dedicated Infiltration Control
Integrated Temperature Reset

Solicite um orçamento. Browse produtos

Introdução do produto

The dry-room dehumidification system is sized around the room envelope, personnel traffic, process exhaust and material transfer rather than a single equipment outlet. It combines filtered return-air recirculation, a low-dew-point desiccant section, outdoor-air treatment, cooling and final temperature reset. Supply and return dew-point sensors feed a central controller that preserves stable room conditions while airlocks and exhaust points introduce changing moisture loads.

Características-chave

A high recirculation ratio repeatedly captures moisture released by personnel, products and door openings before it accumulates in the room.

Separate make-up and return-air paths let the controller treat humid infiltration more aggressively than already dry recirculated air.

Multiple fan and coil sections can be arranged for service continuity without stopping the entire dry-room airflow.

Return-air dew-point measurement represents the room moisture condition and prevents misleading control from an unusually dry supply sample.

Preocupações do produto do cliente

A dry room behaves as a complete moisture-control envelope, so equipment selection must address people, openings, exhaust and surface leakage together.

The supply air reaches its target but the occupied room dew point rises near doors and workstations.High-volume recirculation and distributed supply-return placement sweep local moisture back to the central drying system.

Process exhaust removes conditioned air and pulls humid building air through the envelope.Metered ultra-dry make-up air offsets exhaust while room-pressure control limits uncontrolled infiltration.

A planned filter or fan service event threatens to stop moisture-sensitive production.Parallel fans, isolated filter banks and sectional dampers allow selected components to be maintained while the remaining path operates.

Extremely dry supply air carries excess sensible heat from rotor regeneration and fan power.Dedicated aftercooling and staged chilled-water control remove process heat without adding moisture back to the airstream.

Aplicações típicas

Lithium-ion cell manufacturing dry roomsBattery electrolyte preparation and fillingMoisture-reactive chemical packagingAdvanced battery research pilot linesHygroscopic pharmaceutical production rooms

Parâmetros técnicos

Representative structural ranges for a central dry-room dehumidification and recirculation package are shown below.

Material principal	Low-dew-point composite desiccant rotor with mineral-wool-insulated galvanized or stainless air-handling modules
Painel de espessura	60-100 mm thermally broken double-skin panel construction
Largura efetiva	2200-4800 mm nominal system module width
Comprimento máximo	Up to 12000 mm for combined recirculation drying cooling and fan sections
Aço enfrentando espessura	0.8-1.5 mm coated galvanized or stainless casing skins
Densidade Core	60-100 kg/m³ typical high-density mineral-wool panel insulation
Condutividade térmica	Approximately 0.035-0.043 W/(m·K) for high-density mineral-wool panel insulation
Superfície acabado	Blue powder-coated exterior with smooth galvanized or 304 stainless internal air surfaces
Tipo conjunto	Bolted gasketed modules with thermally broken frames, low-leakage dampers and sealed duct flanges
Customização	Disponível com base na aplicação pretendida e no ambiente operacional.

Opções disponíveis

Duty-standby process fans and isolated filter banksAir-cooled DX or chilled-water temperature-control sectionsElectric steam or gas reactivation with heat recoveryRoom pressure dew-point and energy monitoring through a central PLC

Planning a Dry-Room Dehumidification System specification?

Envie-nos as suas dimensões, condições de instalação, metas de desempenho e acabamento de superfície necessário.

Fale com a nossa equipe