English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
أنظمة توزيع الهواء في الغرف النظيفة
وحدة محطة إعادة تسخين VAV ذات قناة واحدة
A pressure-independent single-duct terminal that meters primary air and reheats the minimum airflow before discharge to a perimeter or process-support zone.
- Pressure-Independent VAV Control
- Integral Hot-Water or Electric Reheat
- Averaging Inlet Flow Sensor
- Acoustically Lined Casing
مقدمة المنتج
The single-duct VAV reheat terminal unit combines a round primary-air inlet, averaging flow sensor, modulating damper and rectangular discharge casing with an integral heating section. During cooling demand, the controller varies primary airflow between programmed minimum and maximum values. When the zone requires heat, airflow is held at the heating minimum while a hot-water valve or staged electric heater raises the discharge temperature. An acoustic liner and optional attenuator control regenerated noise, while coil access panels support inspection of the downstream heating section.
الخصائص الرئيسية
Hot-water or electric reheat adds sensible heat downstream of the control damper without a terminal fan.
Programmed cooling, ventilation and heating minimums allow airflow to follow the zone operating sequence.
Acoustic lining and optional discharge attenuator reduce radiated and air-path noise above occupied spaces.
مخاوف المنتج للعملاء
A reheat terminal must preserve required ventilation airflow, prevent discharge overheating, control noise and keep the heating coil and controller accessible above the ceiling.
Reducing cooling airflow below the ventilation minimum compromises room air exchange.Separate programmed cooling and occupied minimums keep primary air above the required ventilation quantity.
Reheat energizes at too little airflow and produces excessive discharge temperature.Airflow proof and a defined heating minimum enable the coil or heater only when sufficient air passes through the box.
High inlet static pressure produces objectionable regenerated noise over the room.Correct inlet sizing, duct-pressure reset and acoustic attenuation limit velocity and throttling sound.
A leaking water coil valve causes simultaneous cooling and heating energy waste.A tight-closing modulating valve and discharge-air temperature monitoring expose unintended heat input.
تطبيقات نموذجية
Cleanroom perimeter support zonesLaboratory offices and write-up roomsHospital patient and support spacesPharmaceutical corridors and gowning roomsCommercial zones with central cool air
المعلمات الفنية
Representative casing construction ranges for a single-duct VAV terminal with integral reheat are shown below.
| المواد الأساسية | 32–48 kg/m³ mineral-fiber acoustic liner behind galvanized casing with copper-tube aluminum-fin reheat coil |
|---|---|
| سمك اللوحة | 13–25 mm internal acoustic liner |
| العرض الفعال | 300–1000 mm nominal terminal casing width |
| الحد الأقصى الطول | Up to 1800 mm combined terminal, attenuator and reheat-section length |
| الصلب يواجه سمك | 0.7–1.0 mm galvanized casing and access panels |
| الكثافة الأساسية | 32–48 kg/m³ mineral-fiber acoustic lining |
| الموصلية الحرارية | Approximately 0.035–0.045 W/(m·K) for the acoustic liner |
| إنهاء السطح | Mill-galvanized casing with cleanable liner facing and corrosion-protected coil frame |
| نوع المشترك | Round inlet to rectangular lined casing with integral sensor, damper and flanged downstream reheat section |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
One- to four-row hot-water reheat coilStaged or proportional electric heaterIntegral discharge attenuatorFactory-mounted DDC controller and valve package
Planning a Single-Duct VAV Reheat Terminal Unit specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
