English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
FFU ومعدات تنقية الهواء الطرفية
وحدة تصفية مروحة عالية الضغط الثابت
A reinforced deep-plenum FFU with an oversized EC impeller for applications that must preserve airflow against duct resistance or a heavily loaded final filter.
- Deep Reinforced Pressure Plenum
- Oversized Backward-Curved Impeller
- External Pressure-Test Port
- Extended Filter-Loading Reserve
مقدمة المنتج
The high-static-pressure fan filter unit uses a larger backward-curved EC impeller, deep inlet cone and reinforced plenum to generate more pressure than a standard ceiling module. Structural ribs resist panel movement at the higher operating pressure, and an accessible test port allows the fan operating condition or filter resistance to be checked without opening the clean side. This model is suited to ducted inlets, terminal housings with dense filter packs and rooms where the airflow setpoint must be maintained through a longer loading interval.
الخصائص الرئيسية
Formed ribs and reinforced corners limit casing deflection when the plenum operates at elevated static pressure.
A capped pressure port provides a repeatable connection point for commissioning and maintenance measurements.
The EC controller can increase fan speed progressively as filter resistance rises, within the selected operating envelope.
مخاوف المنتج للعملاء
High-resistance systems lose airflow quickly unless the fan, casing and control range are designed for the full pressure path rather than only a clean filter.
A standard FFU falls below the target face velocity when connected to an upstream duct collar.The larger impeller and deep inlet provide the added pressure reserve needed for duct and fitting resistance.
Filter loading changes the delivered airflow long before the final filter reaches a useful service limit.Variable EC speed and pressure reserve allow airflow to be maintained across a broader resistance range.
Thin plenum panels oil-can or leak at seams under elevated internal pressure.Structural ribs, reinforced corners and sealed folds stabilize the housing at the intended operating point.
Technicians cannot distinguish a loaded filter from an incorrectly set fan without opening the ceiling module.The external pressure-test port permits differential-pressure checks from the service side.
تطبيقات نموذجية
Duct-connected cleanroom ceiling systemsTerminal ULPA filtrationClean zones with long prefilter intervalsHigh-resistance recirculation modulesProcess areas requiring stable airflow under variable resistance
المعلمات الفنية
Representative construction ranges for a reinforced high-static-pressure fan filter unit are listed below.
| المواد الأساسية | Reinforced aluminium or steel plenum, oversized backward-curved EC impeller and dense HEPA or ULPA mini-pleat filter |
|---|---|
| سمك اللوحة | 380-500 mm overall module depth |
| العرض الفعال | 575-1170 mm nominal ceiling-grid width |
| الحد الأقصى الطول | Up to 1170 mm standard module length |
| الصلب يواجه سمك | 1.0-1.5 mm reinforced steel housing or structural access panels |
| الكثافة الأساسية | Approximately 90-125 kg/m³ nominal compacted density of the high-capacity micro-glass filter pack |
| الموصلية الحرارية | Approximately 0.035-0.043 W/(m·K) for the high-capacity micro-glass pack used in the high-static-pressure FFU |
| إنهاء السطح | Natural anodized aluminium or light-grey powder coating with contrasting pressure-test hardware |
| نوع المشترك | Reinforced ceiling flange with heavy closed-cell perimeter gasket and gel-seal or compression-seal filter interface |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Duct collar or open top intakeHigh-pressure EC motor and impeller selectionFilter differential-pressure portDeep-pack HEPA or ULPA filter with gel interface
Planning a High-Static-Pressure Fan Filter Unit specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
