Three-quarter view of a high-static-pressure FFU with deep reinforced plenum and oversized EC impeller

FFU 및 터미널 공기 정화 장비

고정압 팬 필터 장치

A reinforced deep-plenum FFU with an oversized EC impeller for applications that must preserve airflow against duct resistance or a heavily loaded final filter.

Deep Reinforced Pressure Plenum
Oversized Backward-Curved Impeller
External Pressure-Test Port
Extended Filter-Loading Reserve

견적 요청 제품 찾아보기

상품 소개

The high-static-pressure fan filter unit uses a larger backward-curved EC impeller, deep inlet cone and reinforced plenum to generate more pressure than a standard ceiling module. Structural ribs resist panel movement at the higher operating pressure, and an accessible test port allows the fan operating condition or filter resistance to be checked without opening the clean side. This model is suited to ducted inlets, terminal housings with dense filter packs and rooms where the airflow setpoint must be maintained through a longer loading interval.

주요 기능

A deep inlet cone guides air smoothly into the oversized impeller and supports pressure development with less recirculation.

Formed ribs and reinforced corners limit casing deflection when the plenum operates at elevated static pressure.

A capped pressure port provides a repeatable connection point for commissioning and maintenance measurements.

The EC controller can increase fan speed progressively as filter resistance rises, within the selected operating envelope.

고객 제품 관심사

High-resistance systems lose airflow quickly unless the fan, casing and control range are designed for the full pressure path rather than only a clean filter.

A standard FFU falls below the target face velocity when connected to an upstream duct collar.The larger impeller and deep inlet provide the added pressure reserve needed for duct and fitting resistance.

Filter loading changes the delivered airflow long before the final filter reaches a useful service limit.Variable EC speed and pressure reserve allow airflow to be maintained across a broader resistance range.

Thin plenum panels oil-can or leak at seams under elevated internal pressure.Structural ribs, reinforced corners and sealed folds stabilize the housing at the intended operating point.

Technicians cannot distinguish a loaded filter from an incorrectly set fan without opening the ceiling module.The external pressure-test port permits differential-pressure checks from the service side.

일반적인 응용 프로그램

Duct-connected cleanroom ceiling systemsTerminal ULPA filtrationClean zones with long prefilter intervalsHigh-resistance recirculation modulesProcess areas requiring stable airflow under variable resistance

기술 매개변수

Representative construction ranges for a reinforced high-static-pressure fan filter unit are listed below.

핵심 재료	Reinforced aluminium or steel plenum, oversized backward-curved EC impeller and dense HEPA or ULPA mini-pleat filter
패널 두께	380-500 mm overall module depth
유효 폭	575 - 1170 mm 공칭 천장 그리드 폭
최대 길이	최대 1170 mm 표준 모듈 길이
강철 면면 두께	1.0-1.5 mm reinforced steel housing or structural access panels
코어 밀도	Approximately 90-125 kg/m³ nominal compacted density of the high-capacity micro-glass filter pack
열전도도 (Thermal Conductivity)	Approximately 0.035-0.043 W/(m·K) for the high-capacity micro-glass pack used in the high-static-pressure FFU
표면 마무리	Natural anodized aluminium or light-grey powder coating with contrasting pressure-test hardware
접합 유형	Reinforced ceiling flange with heavy closed-cell perimeter gasket and gel-seal or compression-seal filter interface
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

Duct collar or open top intakeHigh-pressure EC motor and impeller selectionFilter differential-pressure portDeep-pack HEPA or ULPA filter with gel interface

Planning a High-Static-Pressure Fan Filter Unit specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.