English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
اكسسوارات تركيب الغرف النظيفة
HEPA مرشح المشبك
A stainless swing-bolt HEPA retaining clamp with a broad padded pressure shoe for applying controlled sealing force in room-side filter housings.
- Swing-Bolt Adjustment
- Broad Equi-Bearing Shoe
- Tool-Free Hand Knob
- Padded Stainless Contact
مقدمة المنتج
The clamp pivots away from the filter edge during change-out and swings back into its operating position before compression is applied with the hand knob. Its broad stainless pressure shoe spreads load across the filter frame, while a thin silicone pad protects the contact face. The two-hole base fixes the mechanism to a terminal housing or holding frame without introducing loose service parts.
الخصائص الرئيسية
A broad pressure shoe distributes retention force over more of the filter-frame edge.
The four-lobed knob permits room-side tightening without a separate wrench.
A bonded silicone pad prevents direct metal contact at the loaded surface.
Brushed stainless construction presents smooth exposed surfaces for routine wiping.
مخاوف المنتج للعملاء
HEPA retainers must deliver repeatable compression without damaging the filter frame, creating loose service parts or obstructing room-side replacement.
Narrow fasteners can concentrate force and distort a light-gauge filter frame.The rectangular equi-bearing shoe spreads the applied load over a broad contact area.
Loose nuts and clips are difficult to manage during overhead filter changes.The bolt and pressure arm remain captured by the fixed pivot bracket throughout servicing.
Tool-dependent clamps lengthen room-side replacement and can lead to inconsistent tightening.The large four-lobed hand knob provides direct, visible compression adjustment.
Bare metal pressure faces may scratch coated or anodized filter frames.A bonded black silicone pad separates the stainless shoe from the filter contact surface.
تطبيقات نموذجية
Room-side replaceable HEPA terminal housingsGel-seal and gasket-seal filter holding framesCleanroom ceiling filter modulesPharmaceutical exhaust filter housingsLaboratory and healthcare high-efficiency filter banks
المعلمات الفنية
Typical construction and dimensional ranges for a stainless room-side HEPA filter retaining clamp are listed below.
| المواد الأساسية | 304 stainless-steel pivot bracket, swing bolt, hand knob and pressure shoe with silicone pad |
|---|---|
| سمك اللوحة | 0.8-2.0 mm compatible HEPA filter frame wall thickness |
| العرض الفعال | 40-100 mm pressure-shoe contact width |
| الحد الأقصى الطول | Up to 160 mm overall clamp length |
| الصلب يواجه سمك | 2.0-4.0 mm nominal bracket and shoe thickness |
| الكثافة الأساسية | Approximately 8000 kg/m³ for 304 stainless steel |
| الموصلية الحرارية | Approximately 14-16 W/(m·K) for 304 stainless steel |
| إنهاء السطح | Brushed or passivated stainless steel with a matte black silicone contact pad |
| نوع المشترك | Pivoting captured swing bolt with threaded hand knob and padded equi-bearing shoe |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
304 or 316L stainless-steel constructionM6, M8 or M10 swing-bolt sizeSilicone or EPDM contact padPressure-shoe width matched to the filter frameMounting-hole pattern matched to the terminal housing
Planning a HEPA Filter Clamp specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
