Three-quarter view of a stainless room-side HEPA filter retaining clamp

Aksesori Pemasangan Bilik Bersih

Pengapit penapis HEPA

A stainless swing-bolt HEPA retaining clamp with a broad padded pressure shoe for applying controlled sealing force in room-side filter housings.

Swing-Bolt Adjustment
Broad Equi-Bearing Shoe
Tool-Free Hand Knob
Padded Stainless Contact

Permintaan sebut harga Semak imbas produk

Pengenalan Produk

The clamp pivots away from the filter edge during change-out and swings back into its operating position before compression is applied with the hand knob. Its broad stainless pressure shoe spreads load across the filter frame, while a thin silicone pad protects the contact face. The two-hole base fixes the mechanism to a terminal housing or holding frame without introducing loose service parts.

Ciri-ciri Utama

The captured swing bolt remains attached to the pivot base when released for filter removal.

A broad pressure shoe distributes retention force over more of the filter-frame edge.

The four-lobed knob permits room-side tightening without a separate wrench.

A bonded silicone pad prevents direct metal contact at the loaded surface.

Brushed stainless construction presents smooth exposed surfaces for routine wiping.

Kebimbangan Produk Pelanggan

HEPA retainers must deliver repeatable compression without damaging the filter frame, creating loose service parts or obstructing room-side replacement.

Narrow fasteners can concentrate force and distort a light-gauge filter frame.The rectangular equi-bearing shoe spreads the applied load over a broad contact area.

Loose nuts and clips are difficult to manage during overhead filter changes.The bolt and pressure arm remain captured by the fixed pivot bracket throughout servicing.

Tool-dependent clamps lengthen room-side replacement and can lead to inconsistent tightening.The large four-lobed hand knob provides direct, visible compression adjustment.

Bare metal pressure faces may scratch coated or anodized filter frames.A bonded black silicone pad separates the stainless shoe from the filter contact surface.

Permohonan yang biasa

Room-side replaceable HEPA terminal housingsGel-seal and gasket-seal filter holding framesCleanroom ceiling filter modulesPharmaceutical exhaust filter housingsLaboratory and healthcare high-efficiency filter banks

Parameter teknikal

Typical construction and dimensional ranges for a stainless room-side HEPA filter retaining clamp are listed below.

Bahan Teras	304 stainless-steel pivot bracket, swing bolt, hand knob and pressure shoe with silicone pad
Ketebalan Panel	0.8-2.0 mm compatible HEPA filter frame wall thickness
Lebar berkesan	40-100 mm pressure-shoe contact width
Panjang maksimum	Up to 160 mm overall clamp length
Keluli Menghadapi Ketebalan	2.0-4.0 mm nominal bracket and shoe thickness
Ketumpatan teras	Approximately 8000 kg/m³ for 304 stainless steel
Kekonduksian Terma	Approximately 14-16 W/(m·K) for 304 stainless steel
Kemasan permukaan	Brushed or passivated stainless steel with a matte black silicone contact pad
Jenis Bersatu	Pivoting captured swing bolt with threaded hand knob and padded equi-bearing shoe
Penyesuaian	Boleh didapati berdasarkan aplikasi yang dimaksudkan dan persekitaran operasi.

Pilihan yang boleh didapati

304 or 316L stainless-steel constructionM6, M8 or M10 swing-bolt sizeSilicone or EPDM contact padPressure-shoe width matched to the filter frameMounting-hole pattern matched to the terminal housing

Planning a HEPA Filter Clamp specification?

Hantarkan kepada kami dimensi anda, syarat pemasangan, sasaran prestasi dan kemasan permukaan yang diperlukan.

Berbincang dengan pasukan kami