İngilizce
Almanca
Arapça
Fransızca
Endonezya dilinde
Japonca
Korece
Malay dilinde
Portekizce
Rusça
İspanyolca
Taylandca
TürkçeCurrent
Vietnamca
Temiz Oda Kurulum Aksesuarları
EPDM Gasket
A resilient black EPDM compression gasket formed as a closed loop or cut profile for sealing cleanroom frames, panels and service covers.
- Weather-Resistant EPDM
- Controlled Compression Recovery
- Closed-Loop Frame Seal
- Profile-Specific Fit
Ürün tanıtımı
The EPDM gasket is extruded from black ethylene propylene diene rubber as a hollow or cellular profile with raised sealing ribs. Cut lengths can be joined into rectangular loops for doors, access covers and equipment frames, while continuous profiles suit straight panel interfaces. The compound retains elastic recovery under repeated compression and offers practical resistance to water, ozone, weathering and many dilute cleaning solutions encountered around controlled environments.
Ana Özellikler
A hollow compressible section accommodates hardware tolerances without excessive closing force.
EPDM resists ozone, moisture and outdoor weathering better than many general-purpose rubbers.
Vulcanized or bonded corner joints create a continuous loop around rectangular openings.
Müşteri Ürün Sorunları
A frame gasket must close variable gaps repeatedly while avoiding excessive latch force or permanent compression set.
A solid oversized gasket makes doors difficult to close and overloads latches.The hollow profile compresses progressively so sealing pressure develops without an abrupt closing load.
Flattened rubber fails to recover after long periods under compression.An EPDM compound and section geometry are selected for resilient recovery at the intended squeeze.
Open corner joints become leakage paths around access frames.Factory-vulcanized or carefully bonded mitred corners maintain a continuous closed loop.
Ozone and cleaning moisture crack unsuitable elastomers.Weather-resistant EPDM provides durable service where oil exposure is not the primary requirement.
Tipik uygulamalar
Cleanroom door and hatch framesAccess-panel perimeter sealsAir-handling equipment coversPanel-to-frame compression jointsUtility enclosure doors
Teknik parametreler
Typical construction ranges for a custom extruded EPDM compression gasket are shown below.
| Temel malzemeler | Black EPDM elastomer in hollow, cellular or compact extruded profile |
|---|---|
| Panel kalınlığı | 3-20 mm uncompressed gasket profile height |
| Effective Width (Etkili Genişlik) | 6-40 mm profile contact width |
| Maksimum uzunluk | Up to 50000 mm continuous extrusion or custom closed-loop perimeter |
| Çelik yüz yüze kalınlığı | 0.50-2.00 mm compatible frame flange or retaining channel thickness |
| Core Density (Çekirdek Yoğunluğu) | Approximately 450-750 kg/m³ for cellular EPDM or 1100-1250 kg/m³ for compact EPDM |
| Termal İletkenlik | Approximately 0.06-0.25 W/(m·K), depending on cellular or compact construction |
| Yüzey bitirme | Smooth or fine-textured matte black extruded rubber with defined sealing ribs |
| Ortak tip | Continuous cut length, bonded splice or vulcanized rectangular closed loop |
| Customization (Özelleşme) | Kullanılan uygulama ve çalışma ortamına göre kullanılabilir. |
Mevcut Seçenekler
Hollow or cellular profileSelf-adhesive mounting stripVulcanized closed loopCustom cross-section and corner radius
Planning a EPDM Gasket specification?
Bize boyutlarınızı, montaj koşullarınızı, performans hedeflerinizi ve gerekli yüzey kaplamalarınızı gönderin.
