English
Немецкий
Арабский язык
Французский
Индонезийский
Японский язык
Корейский
Японский
Португальский
Русский языкТекущий
Испанский язык
Тайский
Турецкий
Вьетнамский язык
Системы полы для чистых комнат
Нержавеющая сталь чистых помещений пола плиты
A durable stainless steel floor plate system with a cleanable raised pattern for controlled areas exposed to wash-down, rolling loads or moisture.
- 304 or 316L Stainless Steel
- Cleanable Raised Pattern
- Wet-Area Corrosion Resistance
- Welded Floor Layout
Введение продукции
Stainless steel cleanroom floor plates form a hard-wearing surface where a conventional resin or vinyl finish may be vulnerable to repeated water exposure, concentrated wheel loads or mechanical impact. Each plate is cut from 304 or 316L stainless steel and can be supplied with a rounded-dot or checker pattern. Rounded projections improve shoe contact while leaving fewer tight recesses than a sharp diamond pattern. Plates are fitted over a sound supporting floor, aligned around equipment bases and drains, and joined with sealed or welded seams to create a robust installation that remains accessible to routine cleaning.
Основные характеристики
Rounded or low-profile embossing adds walking grip while allowing cleaning tools to reach between projections.
Sheet widths and cut lengths can be planned around drains, machine plinths and service penetrations to reduce small infill pieces.
Welded and dressed plate joints provide a mechanically strong transition across frequently washed production floors.
Обеспокоенность клиентов продуктами
Metal flooring in a controlled environment must balance traction, cleanability and resistance to the loads concentrated at wheels, feet and equipment supports.
Smooth metal becomes difficult to walk on when rinse water reaches the floor.A rounded-dot or checker surface adds multidirectional shoe contact without applying a sacrificial coating.
Aggressive cleaning quickly exposes chips in painted carbon-steel flooring.Solid 304 or 316L stainless steel retains its corrosion-resistant material through the full plate thickness.
Sharp tread patterns retain residue around narrow corners after wash-down.The optional rounded embossing presents open drainage paths that are easier to sweep and rinse.
Thin sheet flexes and becomes noisy below carts at unsupported edges.Plate gauge, substrate support and welded edge layout are selected together for stable wheel travel.
Типичные приложения
Pharmaceutical wash-down roomsClean utility and equipment areasFood and beverage hygiene zonesMaterial airlocks with wheeled trafficCleanroom service platforms and stairs
Технические параметры
Representative material and fabrication data for hygienic stainless steel floor plates are listed below.
| Основной материал | AISI 304 or 316L austenitic stainless steel floor plate |
|---|---|
| Толщина панели | 3.0–6.0 mm base plate thickness, excluding the raised pattern |
| эффективная ширина | 1000–1250 mm standard plate width |
| Максимальная длина | Up to 3000 mm common cut plate length |
| Толщина линий стали | 3.0–6.0 mm solid stainless steel wearing plate |
| Плотность ядра | Approximately 7900 kg/m³ for the austenitic stainless steel plate |
| Теплопроводимость | Approximately 14–21 W/(m·K), depending on the selected stainless steel grade |
| Поверхностная отделка | Mill-finished rounded-dot or checker embossing with optional brushed flat borders |
| Объединенный тип | Supported butt joint with sealed or continuously welded and dressed stainless steel edges |
| Customization | Доступно в зависимости от предполагаемого применения и операционной среды. |
Доступные варианты
AISI 304 or 316L gradeRounded-dot or checker embossing3.0, 4.5 or 6.0 mm base thicknessCut-outs, formed edges and welded drain interfaces
Planning a Stainless Steel Cleanroom Floor Plates specification?
Отправьте нам ваши габариты, условия монтажа, целевые показатели производительности и требуемую отделку поверхности.
