Complete stainless steel cleanroom floor plate with rounded anti-slip embossing

클린룸 바닥 시스템

스테인레스 스틸 클린룸 바닥 판

A durable stainless steel floor plate system with a cleanable raised pattern for controlled areas exposed to wash-down, rolling loads or moisture.

304 or 316L Stainless Steel
Cleanable Raised Pattern
Wet-Area Corrosion Resistance
Welded Floor Layout

견적 요청 제품 찾아보기

상품 소개

Stainless steel cleanroom floor plates form a hard-wearing surface where a conventional resin or vinyl finish may be vulnerable to repeated water exposure, concentrated wheel loads or mechanical impact. Each plate is cut from 304 or 316L stainless steel and can be supplied with a rounded-dot or checker pattern. Rounded projections improve shoe contact while leaving fewer tight recesses than a sharp diamond pattern. Plates are fitted over a sound supporting floor, aligned around equipment bases and drains, and joined with sealed or welded seams to create a robust installation that remains accessible to routine cleaning.

주요 기능

Austenitic stainless steel resists corrosion and does not rely on a painted surface that can peel away under traffic.

Rounded or low-profile embossing adds walking grip while allowing cleaning tools to reach between projections.

Sheet widths and cut lengths can be planned around drains, machine plinths and service penetrations to reduce small infill pieces.

Welded and dressed plate joints provide a mechanically strong transition across frequently washed production floors.

고객 제품 관심사

Metal flooring in a controlled environment must balance traction, cleanability and resistance to the loads concentrated at wheels, feet and equipment supports.

Smooth metal becomes difficult to walk on when rinse water reaches the floor.A rounded-dot or checker surface adds multidirectional shoe contact without applying a sacrificial coating.

Aggressive cleaning quickly exposes chips in painted carbon-steel flooring.Solid 304 or 316L stainless steel retains its corrosion-resistant material through the full plate thickness.

Sharp tread patterns retain residue around narrow corners after wash-down.The optional rounded embossing presents open drainage paths that are easier to sweep and rinse.

Thin sheet flexes and becomes noisy below carts at unsupported edges.Plate gauge, substrate support and welded edge layout are selected together for stable wheel travel.

일반적인 응용 프로그램

Pharmaceutical wash-down roomsClean utility and equipment areasFood and beverage hygiene zonesMaterial airlocks with wheeled trafficCleanroom service platforms and stairs

기술 매개변수

Representative material and fabrication data for hygienic stainless steel floor plates are listed below.

핵심 재료	AISI 304 or 316L austenitic stainless steel floor plate
패널 두께	3.0–6.0 mm base plate thickness, excluding the raised pattern
유효 폭	1000–1250 mm standard plate width
최대 길이	Up to 3000 mm common cut plate length
강철 면면 두께	3.0–6.0 mm solid stainless steel wearing plate
코어 밀도	Approximately 7900 kg/m³ for the austenitic stainless steel plate
열전도도 (Thermal Conductivity)	Approximately 14–21 W/(m·K), depending on the selected stainless steel grade
표면 마무리	Mill-finished rounded-dot or checker embossing with optional brushed flat borders
접합 유형	Supported butt joint with sealed or continuously welded and dressed stainless steel edges
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

AISI 304 or 316L gradeRounded-dot or checker embossing3.0, 4.5 or 6.0 mm base thicknessCut-outs, formed edges and welded drain interfaces

Planning a Stainless Steel Cleanroom Floor Plates specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.