Brushed stainless cleanroom exhaust air grille with removable slotted face

Системы распределения воздуха в чистых помещениях

Выхлопная воздушная решетка в чистой комнате

A stainless-steel exhaust grille with a removable cleanable face and rear metal-mesh separator for controlled extraction from hygiene-sensitive rooms.

Stainless Hygienic Face
Removable Lint Separator
Low-Level Extraction
Autoclave-Capable Front Panel

Запрос котировки Просмотреть продукты

Введение продукции

The cleanroom exhaust air grille is built for locations where the visible extract terminal must tolerate frequent disinfection and capture fibres before they enter the duct. A smooth 304 stainless-steel face protects a removable expanded-metal or woven-wire separator that traps lint without using disposable fibrous media at room level. Quarter-turn retainers release the front panel for cleaning, and the recessed mounting sleeve connects the grille directly to the exhaust branch. Rounded edges and flush fasteners reduce snagging around low-level wall installations.

Основные характеристики

A non-porous stainless front panel withstands routine disinfectant wipe-down and repeated handling.

The reusable metal-mesh separator captures textile lint before it deposits in the exhaust duct.

Room-side retainers allow both grille and separator to be removed without entering the service void.

A shallow recessed sleeve keeps the visible face close to the cleanroom wall plane.

Обеспокоенность клиентов продуктами

Hygienic exhaust terminals face lint loading, repeated chemical cleaning and restricted access at low wall level.

Garment fibres accumulate inside an inaccessible exhaust branch.A removable stainless mesh separator intercepts lint at the room boundary before it reaches the duct.

Paint chips or degrades under repeated hospital disinfectants.The visible panel uses corrosion-resistant stainless steel without a vulnerable decorative coating.

Sharp grille edges damage cleaning cloths and protective garments.Folded radiused edges and flush retainers leave a smooth perimeter around the opening.

Maintenance staff cannot reach the rear separator from the corridor side.The face and mesh pack both withdraw directly into the clean room for controlled cleaning.

Типичные приложения

Operating-room and treatment-area exhaustPharmaceutical gowning exhaustSterile laundry and clean utility roomsCleanroom low-wall extractionLaboratory support-space exhaust

Технические параметры

Representative construction ranges for a hygienic stainless cleanroom exhaust grille are listed below.

Основной материал	304 stainless-steel front panel and frame with removable stainless expanded-metal or woven-mesh separator
Толщина панели	0.8–1.5 mm stainless front panel and mounting sleeve
эффективная ширина	300–1000 mm nominal exhaust face width
Максимальная длина	Up to 1200 mm for rectangular wall grilles
Толщина линий стали	0.8–1.5 mm 304 stainless-steel visible panel
Плотность ядра	Approximately 8000 kg/m³ for the 304 stainless-steel grille components
Теплопроводимость	Approximately 14–16 W/(m·K) for the 304 stainless-steel grille components
Поверхностная отделка	Brushed, bead-blasted or electropolished stainless steel with smooth folded edges
Объединенный тип	Quarter-turn removable face on a gasketed recessed wall sleeve with rear duct flange
Customization	Доступно в зависимости от предполагаемого применения и операционной среды.

Доступные варианты

304 or 316L stainless-steel constructionPerforated or horizontal-slot visible faceExpanded-metal or woven-wire lint separatorFlush wall sleeve for sandwich-panel installation

Planning a Cleanroom Exhaust Air Grille specification?

Отправьте нам ваши габариты, условия монтажа, целевые показатели производительности и требуемую отделку поверхности.

Поговорите с нашей командой