Brushed stainless cleanroom exhaust air grille with removable slotted face

클린룸 공기 분배 시스템

클린룸 배기 공기 그릴

A stainless-steel exhaust grille with a removable cleanable face and rear metal-mesh separator for controlled extraction from hygiene-sensitive rooms.

Stainless Hygienic Face
Removable Lint Separator
Low-Level Extraction
Autoclave-Capable Front Panel

견적 요청 제품 찾아보기

상품 소개

The cleanroom exhaust air grille is built for locations where the visible extract terminal must tolerate frequent disinfection and capture fibres before they enter the duct. A smooth 304 stainless-steel face protects a removable expanded-metal or woven-wire separator that traps lint without using disposable fibrous media at room level. Quarter-turn retainers release the front panel for cleaning, and the recessed mounting sleeve connects the grille directly to the exhaust branch. Rounded edges and flush fasteners reduce snagging around low-level wall installations.

주요 기능

A non-porous stainless front panel withstands routine disinfectant wipe-down and repeated handling.

The reusable metal-mesh separator captures textile lint before it deposits in the exhaust duct.

Room-side retainers allow both grille and separator to be removed without entering the service void.

A shallow recessed sleeve keeps the visible face close to the cleanroom wall plane.

고객 제품 관심사

Hygienic exhaust terminals face lint loading, repeated chemical cleaning and restricted access at low wall level.

Garment fibres accumulate inside an inaccessible exhaust branch.A removable stainless mesh separator intercepts lint at the room boundary before it reaches the duct.

Paint chips or degrades under repeated hospital disinfectants.The visible panel uses corrosion-resistant stainless steel without a vulnerable decorative coating.

Sharp grille edges damage cleaning cloths and protective garments.Folded radiused edges and flush retainers leave a smooth perimeter around the opening.

Maintenance staff cannot reach the rear separator from the corridor side.The face and mesh pack both withdraw directly into the clean room for controlled cleaning.

일반적인 응용 프로그램

Operating-room and treatment-area exhaustPharmaceutical gowning exhaustSterile laundry and clean utility roomsCleanroom low-wall extractionLaboratory support-space exhaust

기술 매개변수

Representative construction ranges for a hygienic stainless cleanroom exhaust grille are listed below.

핵심 재료	304 stainless-steel front panel and frame with removable stainless expanded-metal or woven-mesh separator
패널 두께	0.8–1.5 mm stainless front panel and mounting sleeve
유효 폭	300–1000 mm nominal exhaust face width
최대 길이	Up to 1200 mm for rectangular wall grilles
강철 면면 두께	0.8–1.5 mm 304 stainless-steel visible panel
코어 밀도	Approximately 8000 kg/m³ for the 304 stainless-steel grille components
열전도도 (Thermal Conductivity)	Approximately 14–16 W/(m·K) for the 304 stainless-steel grille components
표면 마무리	Brushed, bead-blasted or electropolished stainless steel with smooth folded edges
접합 유형	Quarter-turn removable face on a gasketed recessed wall sleeve with rear duct flange
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

304 or 316L stainless-steel constructionPerforated or horizontal-slot visible faceExpanded-metal or woven-wire lint separatorFlush wall sleeve for sandwich-panel installation

Planning a Cleanroom Exhaust Air Grille specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.