Anglais
Allemand
Arabe
FrançaisCurrent
Indonésien
Japonais
Coréen
Le malais
Le portugais
russe
espagnol
Thaïlandais
Le turc
Le vietnamien
Cleanroom mur et systèmes de plafond
Cleanroom Return-Air Riser Panneau mural
A 100 mm hollow wall module that combines a vertical return-air pathway, low-level intake grille and optional pre-filter within the cleanroom partition, avoiding a projecting external return duct.
- Concealed Return-Air Path
- Low-Level Intake Grille
- Flush Wall Integration
- Accessible Pre-Filter Option
Introduction de produit
The Cleanroom Return-Air Riser Wall Panel replaces a separate floor-to-ceiling return column with a prefabricated hollow module. Room air enters through a flush grille near floor level, travels upward inside a protected channel and connects to the recirculation plenum or return duct above the ceiling. Gypsum lining and aluminum honeycomb reinforcement stiffen the wide cavity without blocking airflow. A lift-out or hinged intake section gives maintenance access to the optional coarse pre-filter while the remaining wall face stays aligned with adjacent cleanroom panels.
Key Features
Low-wall collection removes air near the zone where heavier particles tend to settle.
A flush stainless steel or coated grille preserves a smooth partition profile.
The optional washable pre-filter can be reached from the clean side through a dedicated cover.
Factory-formed top and bottom transitions reduce leakage around the riser connection.
Préoccupations du client produit
Return-wall concerns center on lost floor space, inaccessible filters, noisy air velocity and leakage at duct transitions.
Conventional boxed return columns project into the cleanroom and reduce usable floor area.The hollow riser occupies the same plane and modular width as the surrounding partition.
A concealed pre-filter becomes difficult to wash when there is no clean-side access.A removable lower grille exposes the filter without opening the complete wall assembly.
An undersized intake creates excessive velocity and objectionable airflow noise.Single- or double-riser grille areas can be selected to provide a broader low-level return path.
Gaps at the ceiling connection allow air to bypass the intended return route.A formed top collar and sealed vertical channel direct the captured air into the return plenum.
Les applications typiques
Pharmaceutical rooms with top-supply and low-return airflowCleanroom gowning and airlock areasMedical-device rooms using concealed return-air risersLaboratories with concealed recirculation pathsSpace-constrained clean manufacturing rooms
Paramètres techniques
This specification follows the common 100 mm integrated return-air wall module used in modular cleanroom systems.
| Matériaux de base | 12 mm gypsum liner with aluminum honeycomb reinforcement around a hollow air channel |
|---|---|
| Panneau épaisseur | 100 mm |
| Largeur effective | 980 ou 1180 mm |
| Longueur maximale | 6000 mm |
| Acier face épaisseur | 0.50 mm |
| Densité Core | 750–900 kg/m³ gypsum liner and approximately 27 kg/m³ aluminum honeycomb |
| Conductivité thermique | 0.17–0.25 W/(m·K) for the lined air-channel assembly |
| surface finie | PE-, HDP- or PVDF-coated steel; stainless steel intake face available |
| Type joint | Sealed hollow tongue-and-groove riser with flush removable return grille |
| Customisation | Riser width, grille size and filter access can be adapted to the intended airflow arrangement |
Options disponibles
Single- or double-riser airflow channelAluminum or stainless steel low return grilleWashable coarse pre-filter cassetteHinged or lift-out clean-side access cover
Planning a Cleanroom Return-Air Riser Wall Panel specification?
Envoyez-nous vos dimensions, conditions d'installation, objectifs de performance et finition de surface requise.
