English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
مرشحات الهواء والترشيح الكيميائي
HEPA مرشح ضغط طوقا
A continuous closed-cell elastomer gasket that compresses between the HEPA frame and housing flange to stop perimeter air bypass.
- Closed-Cell Construction
- Controlled Compression
- Continuous Corner Joint
- Multiple Elastomer Grades
مقدمة المنتج
The compression gasket is bonded to the upstream or downstream face of a HEPA frame and seals against a flat housing flange. Closed-cell polyurethane, neoprene, EPDM or silicone limits air transmission through the foam itself, while the selected hardness lets the gasket recover after clamping. Mitered, vulcanized or moulded endless corners remove gaps at the perimeter. Adhesive backing holds the profile in position during filter installation.
الخصائص الرئيسية
Defined thickness and hardness provide a predictable compression window.
Endless or sealed mitered corners eliminate open butt joints.
Pressure-sensitive adhesive keeps the profile aligned on the filter frame.
مخاوف المنتج للعملاء
Perimeter leakage can remain even with an efficient filter if the gasket is porous, misaligned or unevenly compressed.
Open-cell foam allows air to pass through the gasket body.Closed-cell polyurethane, neoprene or silicone forms a substantially less permeable seal.
A butt joint opens at the frame corner.Moulded endless or sealed mitered construction closes the entire perimeter.
Over-tightening permanently flattens the gasket.Specified hardness and clamp travel keep compression within the elastic recovery range.
The strip moves out of position while the filter is inserted.A continuous adhesive backing fixes the gasket to the cleaned frame surface.
تطبيقات نموذجية
Gasket-seal HEPA filtersAbsolute filter holding framesSide-access filter housingsCleanroom terminal boxesReplacement filter-bank seals
المعلمات الفنية
Common material and dimensional ranges for HEPA compression gaskets are listed below.
| المواد الأساسية | Closed-cell polyurethane, neoprene, EPDM or silicone elastomer foam |
|---|---|
| سمك اللوحة | 5–12 mm uncompressed gasket thickness |
| العرض الفعال | 12–25 mm gasket strip width |
| الحد الأقصى الطول | Up to 5000 mm continuous coil or custom endless perimeter |
| الصلب يواجه سمك | 0.05–0.15 mm reinforced pressure-sensitive adhesive carrier where used |
| الكثافة الأساسية | 80–250 kg/m³ closed-cell foam density |
| الموصلية الحرارية | 0.04–0.08 W/(m·K) depending on elastomer grade |
| إنهاء السطح | Smooth black, grey or white closed-cell skin with adhesive backing |
| نوع المشترك | Moulded endless loop or sealed 45-degree miter joints bonded to the filter frame |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Polyurethane, neoprene, EPDM or siliconeSelf-adhesive strip or moulded loopFlat or hollow profileCustom die-cut frame gasket
Planning a HEPA Filter Compression Gasket specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
