Water-cooled chiller with compressor and shell-and-tube heat exchangers

Temiz Oda HVAC ve Hava İşleme Ekipmanları

Su Soğutmalı Soğutma Chiller

An indoor liquid chiller that transfers condenser heat to a cooling-water loop for efficient, stable chilled-water production at medium and large loads.

Stable Indoor Operation
High Heat-Exchanger Efficiency
Screw or Centrifugal Compression
Cooling-Water Heat Rejection

Alıntı isteği Browse ürünleri

Ürün tanıtımı

The water-cooled chiller uses a refrigerant evaporator to cool the cleanroom chilled-water loop and a separate condenser to transfer heat into cooling-tower or process water. Because condensing temperature is controlled by water rather than hot roof air, the unit can achieve stable performance and compact indoor placement at large capacity. Screw compressors provide robust staged or variable capacity, while centrifugal machines suit still larger duty. Water flow, fouling allowance and treatment are coordinated for both heat exchangers.

Ana Özellikler

Cooling-water heat rejection maintains lower and more stable condensing conditions than ambient-air coils.

Shell-and-tube heat exchangers provide serviceable water circuits for medium and large plant capacities.

Variable compressor capacity follows cleanroom load without relying only on compressor cycling.

Indoor installation protects refrigeration equipment from outdoor weather and airborne debris.

Müşteri Ürün Sorunları

A water-cooled chiller depends on both the chilled-water and condenser-water systems; poor flow or fouling on either side reduces plant performance.

Scale on condenser tubes raises refrigerant pressure and compressor power.Water treatment, strainers and serviceable tube bundles limit and remove fouling.

Low evaporator flow risks freezing and unstable leaving-water temperature.Flow proof, minimum-flow control and staged capacity protect the evaporator.

A single large chiller operates inefficiently during night or low-production load.Variable capacity and multi-chiller sequencing keep active equipment within an efficient range.

Plant-room pipe forces distort heat-exchanger nozzles.Independent pipe supports and flexible connectors isolate external loads from the chiller.

Tipik uygulamalar

Large pharmaceutical campusesSemiconductor chilled-water plantsHospital clean-area systemsIndustrial process coolingCentral laboratory facilities

Teknik parametreler

Typical construction and evaporator insulation data for an indoor water-cooled chiller are shown below.

Temel malzemeler	Closed-cell elastomeric sheet on the evaporator, waterboxes and suction elbow
Panel kalınlığı	1.0–2.0 mm removable compressor and control enclosure panels
Effective Width (Etkili Genişlik)	1200–3000 mm nominal equipment width
Maksimum uzunluk	Up to 8000 mm including compressor and shell-and-tube exchangers
Çelik yüz yüze kalınlığı	1.0–2.5 mm enclosure sheet with heavier welded base steel
Core Density (Çekirdek Yoğunluğu)	52.5 kg/m³ nominal closed-cell elastomeric insulation
Termal İletkenlik	0.033 W/(m·K) at 0°C for the evaporator insulation
Yüzey bitirme	Powder-coated structural steel and removable panels with insulated cold-surface piping
Ortak tip	Welded skid base with bolted compressor enclosure and flanged or grooved water connections
Customization (Özelleşme)	Kullanılan uygulama ve çalışma ortamına göre kullanılabilir.

Mevcut Seçenekler

Fixed-speed or variable-speed screw compressorScrew or centrifugal compressor platformMarine water boxes and removable tube bundlesAcoustic enclosure and heat-recovery condenser

Planning a Water-Cooled Chiller specification?

Bize boyutlarınızı, montaj koşullarınızı, performans hedeflerinizi ve gerekli yüzey kaplamalarınızı gönderin.

Ekibimizle konuşun