English
Немецкий
Арабский язык
Французский
Индонезийский
Японский язык
Корейский
Японский
Португальский
Русский языкТекущий
Испанский язык
Тайский
Турецкий
Вьетнамский язык
Системы полы для чистых комнат
Нержавеющая сталь чистой комнаты пол покрытия полоса
A slim stainless steel bridge strip that covers butt joints between adjacent floor finishes and shields their exposed edges at cleanroom thresholds and transitions.
- 30–50 mm Cover Widths
- Low-Profile Transition
- Protected Flooring Edges
- Countersunk Fixing
Введение продукции
The stainless steel cleanroom floor cover strip spans the meeting line between floor coverings of the same or slightly different height. Its shallow curved section hides small cut-edge irregularities and prevents wheels or footwear from catching the exposed material edge. Side-drilled countersunk holes keep fastener heads level with the polished or matt surface, while a 2.7 metre standard length reduces unnecessary joins across common door openings. Unlike a movement joint, this strip is intended to bridge and protect a stable finish transition rather than absorb structural displacement.
Основные характеристики
A shallow curved bridge smooths minor height differences without creating a bulky threshold ramp.
Countersunk holes receive flush fixings that do not project into the wheel path.
Several widths cover different edge tolerances while keeping the visible strip proportionate to the opening.
Обеспокоенность клиентов продуктами
A stable floor-covering joint still requires edge protection when cut lines, slight height differences and repeated doorway traffic meet in one location.
Cart wheels catch a small raised edge where two floor finishes meet.The curved cover strip bridges the join and provides a continuous metal crossing surface.
Cleaning and traffic gradually fray or chip an exposed vinyl or resin edge.The stainless steel face shields both finish margins from direct contact.
Proud screw heads create dirt-catching points along a threshold plate.Side-drilled countersunk holes allow compatible fasteners to finish flush with the strip.
A short trim requires multiple visible joins across a wide doorway.The 2700 mm standard length can span most single and double cleanroom openings in one piece.
Типичные приложения
Cleanroom door thresholdsVinyl-to-resin floor transitionsStable repaired flooring seamsGowning room entrancesLaboratory corridor finish changes
Технические параметры
Representative dimensions and materials for a stainless steel floor-covering protection strip are listed below.
| Основной материал | Solid austenitic stainless steel cover strip for interior flooring transitions |
|---|---|
| Толщина панели | 1.0–2.0 mm solid strip thickness, depending on cover width |
| эффективная ширина | 30–50 mm exposed bridge width |
| Максимальная длина | 2700 mm standard straight strip length |
| Толщина линий стали | 1.0–2.0 mm full-thickness stainless steel facing |
| Плотность ядра | About 7900 kg/m³ for the solid austenitic stainless steel strip |
| Теплопроводимость | Approximately 14–21 W/(m·K) for common austenitic stainless steel grades |
| Поверхностная отделка | Polished or matt stainless steel with deburred longitudinal edges |
| Объединенный тип | Side-drilled and countersunk mechanically fixed bridge over a stable flooring butt joint |
| Customization | Доступно в зависимости от предполагаемого применения и операционной среды. |
Доступные варианты
30, 40 or 50 mm cover widthPolished or matt stainless steel finishPre-drilled or undrilled supplyCut length and custom countersunk hole spacing
Planning a Stainless Steel Cleanroom Floor Cover Strip specification?
Отправьте нам ваши габариты, условия монтажа, целевые показатели производительности и требуемую отделку поверхности.
