Industrial desiccant rotor dehumidifier with blue modular service doors

クリーンルーム HVAC および空気処理装置

産業用乾燥剤ロータ除湿機

A dual-air-stream dehumidifier that continuously adsorbs water vapor on a slowly rotating desiccant wheel and releases it into a heated reactivation airstream.

Continuous Desiccant Rotation
Separated Process and Reactivation Air
Low-Temperature Moisture Removal
Modular Service Sections

見積もりリクエスト製品案内

商品紹介

The industrial desiccant rotor dehumidifier divides a high-surface-area desiccant wheel between process and reactivation sectors. The process fan sends humid air through the dry portion of the rotor, while a separate heated airflow drives captured moisture out of the rotating media and discharges it outdoors. Sealed sector plates, filters and controlled rotor speed maintain a stable moisture balance even when the room temperature is too low for efficient refrigerant condensation.

主要な特徴

A silica-gel or molecular-sieve composite wheel presents thousands of parallel channels with low airflow resistance.

Independent process and reactivation fans prevent the wet exhaust stream from re-entering the dry-air outlet.

Electric, steam or gas reactivation choices match available utilities and operating-cost priorities.

Separate access doors expose filters, rotor drive, seals and heater components without disturbing adjacent air-treatment sections.

お客様の製品に関する懸念事項

Refrigeration alone loses dehumidification capacity at low temperature and cannot economically reach many process humidity targets.

A cold production room remains humid even though the cooling coil operates continuously.Desiccant adsorption removes vapor without requiring the process air to cross a refrigerated dew-point surface.

Leakage between wet reactivation air and dry process air causes unstable outlet moisture.Adjustable sector seals and balanced fan pressures maintain physical separation across the rotating wheel.

An overloaded prefilter contaminates the rotor face and increases pressure drop.Dedicated process and reactivation filter stages are accessible from separate service doors for scheduled replacement.

A fixed reactivation heater consumes full energy during a reduced moisture load.Modulating heater output and variable rotor speed reduce regeneration input as the required dry-air condition changes.

典型的な用途

Pharmaceutical powder processing roomsMoisture-sensitive electronics assemblyCold storage and freezer anteroomsControlled raw-material warehousesDry-air supply for laboratory equipment

技術的なパラメータ

Typical modular construction ranges for an industrial rotary desiccant dehumidifier are provided below.

コア材料	Silica-gel or molecular-sieve composite honeycomb rotor inside a mineral-wool-insulated galvanized steel casing
パネルの厚さ	30-50 mm double-skin insulated casing panel thickness
有効幅	900-2600 mm nominal process-section width
最大長さ	Up to 5500 mm overall modular unit length
鋼鉄の厚さを直面する	0.8-1.2 mm galvanized or pre-painted steel inner and outer skins
コア密度	40-80 kg/m³ typical mineral-wool casing insulation density
熱伝導率	Approximately 0.036-0.045 W/(m·K) for the mineral-wool casing fill
表面仕上げ	Blue powder-coated access panels with galvanized internal frame and corrosion-resistant rotor housing
ジョイントタイプ	Cam-lock or bolted modular casing with gasketed doors, flexible duct collars and sealed rotor-sector interfaces
カスタマイズ	意図したアプリケーションと動作環境に基づいて利用できます。

利用可能なオプション

Electric, steam or gas-fired reactivation heaterPrecooling and aftercooling coil modulesMERV 8 through high-efficiency final filtrationVariable-speed process fan and dew-point control package

Planning a Industrial Desiccant Rotor Dehumidifier specification?

寸法、設置条件、性能目標、必要な表面仕上げをお送りください。

チームに相談する