Fresh-air dehumidification unit with weather louver blue service doors and supply fan

Cleanroom HVAC dan Peralatan Penanganan Udara

Unit Dehumidifikasi Udara Segar

A packaged outdoor-air unit that filters, cools, dries and tempers humid make-up air before it enters a cleanroom air-handling or pressure-control system.

100 Percent Outdoor-Air Treatment
Cooling Plus Desiccant Drying
Recovered Condenser Heat
Cleanroom Pressure Support

Permintaan untuk kutipan Browse Produk

Perkenalan produk

The fresh-air dehumidification unit treats the ventilation and replacement air that creates the largest seasonal latent load in many cleanrooms. A prefilter and cooling coil remove heat and bulk moisture, the desiccant section lowers the dew point, and recovered condenser or reactivation heat tempers the leaving air. Weather-resistant louvers, drainable coil sections and pressure-capable fans allow the unit to supply dry make-up air without burdening the recirculation AHU.

Fitur utama:

A full outdoor-air intake path isolates ventilation moisture before it reaches the cleanroom recirculation system.

Mechanical cooling handles high-temperature bulk condensation while the desiccant stage addresses the remaining vapor load.

Recovered refrigeration heat can temper overcooled air and reduce separate reheat energy.

Low-leakage dampers and variable-speed supply control maintain the scheduled make-up airflow as filters load.

Kekhawatiran produk pelanggan

Untreated outdoor air can overwhelm the sensible and latent capacity of a cleanroom recirculation unit, especially during humid weather.

Summer ventilation air drives room humidity above the process limit despite adequate recirculation cooling.The dedicated unit removes outdoor latent load before the make-up air joins the cleanroom supply stream.

Deep cooling alone produces air that is dry enough but too cold for direct delivery.Recovered condenser heat or a controlled heating coil resets the dry air to the required supply temperature.

A dirty intake filter reduces make-up airflow and weakens cleanroom positive pressure.Differential-pressure monitoring and variable-speed fan control preserve scheduled airflow and signal filter service.

Rain and wind-driven moisture enter through an exposed outside-air opening.A weather louver, drainable intake plenum and sloped stainless drain pan separate liquid water before the treatment sections.

Aplikasi yang Tipis

Positive-pressure pharmaceutical cleanroomsLaboratory ventilation make-up airMedical-device manufacturing suitesElectronics plants in humid climatesClean corridors serving process exhaust rooms

Parameter teknis

Typical casing and dimensional ranges for a packaged cleanroom fresh-air dehumidification unit are shown below.

Bahan inti	Cooling coil and desiccant rotor in a mineral-wool-insulated galvanized steel air-handling casing
Ketebalan Panel (Panel Thickness)	40-60 mm double-skin insulated casing panel thickness
Efektif lebar	1200-3500 mm nominal outdoor-air unit width
Panjang maksimum	Up to 7500 mm including intake filtration cooling rotor and supply-fan sections
Baja menghadap ketebalan	0.8-1.2 mm pre-painted outer skin and galvanized or stainless inner skin
Kepadatan inti (core density)	45-80 kg/m³ typical mineral-wool casing insulation density
Konduktivitas Termal (Thermal Conductivity)	Approximately 0.035-0.045 W/(m·K) for mineral-wool casing insulation
Permukaan selesai	White weather-resistant powder coating with light-blue service doors and stainless wet-section surfaces
Jenis Bersama	Bolted gasketed casing modules with flanged duct openings, flexible fan connections and welded drain pan
Customization (Kustomisasi)	Tersedia berdasarkan aplikasi yang dimaksudkan dan lingkungan operasi.

Pilihan yang tersedia

Direct-expansion or chilled-water cooling sectionDesiccant wheel with electric steam or gas reactivationMERV 8 prefilter through high-efficiency final filter stagesOutdoor roof curb, weather hood and remote building-network controls

Planning a Fresh-Air Dehumidification Unit specification?

Kirimkan kami dimensi Anda, kondisi instalasi, target kinerja dan permukaan akhir yang diperlukan.

Bicaralah dengan tim kami