Three-quarter view of a low-noise fan filter unit with acoustic lining and isolated EC fan

FFU dan Peralatan Penulenan Udara Terminal

Unit Penapis Kipas Bunyi Rendah

A quiet EC-powered FFU that combines motor isolation, a rounded inlet and an acoustic-lined plenum to reduce tonal noise above occupied cleanroom work areas.

Acoustic-Lined Pressure Plenum
Elastomeric Motor Isolation
Low-Turbulence Inlet Bell
Quiet Variable-Speed EC Drive

Permintaan sebut harga Semak imbas produk

Pengenalan Produk

The low-noise fan filter unit controls airborne and structure-borne sound at their main sources. A backward-curved EC fan sits on elastomeric isolators, while a smooth inlet bell reduces separation noise entering the wheel. Selected interior surfaces carry cleanable encapsulated acoustic lining, and the outlet baffle moderates local velocity peaks before the final filter. The result is intended for continuously occupied rooms where speech, concentration and operator comfort matter alongside particulate control.

Ciri-ciri Utama

Elastomeric fan mounts reduce the vibration transferred from the rotating assembly into the plenum and ceiling grid.

A radiused intake bell lowers inlet turbulence and the broadband noise associated with a sharp-edged opening.

Encapsulated acoustic lining absorbs internal fan noise without exposing loose fibers to the clean-air path.

Continuous EC speed control allows the unit to operate at the lowest practical rotational speed for the required airflow.

Kebimbangan Produk Pelanggan

A quiet FFU must reduce fan and vibration noise without placing porous or shedding materials in the downstream clean-air path.

A tonal motor sound becomes tiring when operators work directly below FFUs for a full shift.The EC motor, rounded inlet and optimized backward-curved wheel reduce the dominant rotating and inlet tones.

Fan vibration travels through a rigid casing and turns the suspended ceiling into a sounding board.Elastomeric mounts interrupt the structural transmission path between the fan and the module frame.

Unprotected fibrous acoustic foam could shed particles into the clean airflow.The selected sound-absorbing liner is sealed behind a cleanable perforated facing on the upstream plenum surfaces.

A unit selected at maximum speed remains unnecessarily loud after room balancing.Variable EC control lets each module run only fast enough to meet the measured airflow setpoint.

Permohonan yang biasa

Pharmaceutical inspection roomsClean laboratories with seated operatorsMedical-device assembly areasHospital pharmacy cleanroomsMetrology and optical inspection spaces

Parameter teknikal

Typical materials and dimensional ranges for an acoustically treated low-noise fan filter unit are shown below.

Bahan Teras	Powder-coated steel plenum, isolated EC centrifugal fan, encapsulated acoustic liner and HEPA or ULPA filter pack
Ketebalan Panel	300-420 mm overall module depth
Lebar berkesan	575-1170 mm nominal ceiling-grid width
Panjang maksimum	Up to 1170 mm standard module length
Keluli Menghadapi Ketebalan	0.8-1.2 mm formed steel housing and perforated acoustic-liner facing
Ketumpatan teras	Approximately 24-40 kg/m³ nominal density of the encapsulated acoustic liner
Kekonduksian Terma	Approximately 0.032-0.040 W/(m·K) for the dry acoustic-liner material
Kemasan permukaan	White low-gloss powder coating with sealed dark acoustic lining confined to the upstream plenum
Jenis Bersatu	Vibration-isolated drop-in flange with closed-cell ceiling gasket and compression-sealed filter frame
Penyesuaian	Boleh didapati berdasarkan aplikasi yang dimaksudkan dan persekitaran operasi.

Pilihan yang boleh didapati

Acoustic-lined or standard plenumLow-sound EC motor selectionRemote speed controller or network interfaceLow-resistance final filter sized for reduced fan speed

Planning a Low-Noise Fan Filter Unit specification?

Hantarkan kepada kami dimensi anda, syarat pemasangan, sasaran prestasi dan kemasan permukaan yang diperlukan.

Berbincang dengan pasukan kami