Industrial refrigerant dehumidifier with top discharge fan and wheeled cabinet

Bilik Bersih HVAC dan Peralatan Pengendalian Udara

Dehumidifier penyejuk industri

A self-contained condensation dehumidifier that cools process air below its dew point, drains the collected water and reheats the dry air through the condenser.

Refrigeration Moisture Removal
Automatic Hot-Gas Defrost
Continuous Condensate Pumping
Digital Humidity Control

Permintaan sebut harga Semak imbas produk

Pengenalan Produk

The industrial refrigerant dehumidifier combines a washable inlet filter, direct-expansion evaporator, compressor, condenser and centrifugal fan in one wheeled cabinet. Moist air condenses on the cold evaporator, then passes over the condenser so the discharged air is dry and slightly warmer. A built-in controller, hot-gas defrost and pumped drain support unattended humidity control in clean production and support spaces operating above typical refrigeration frost limits.

Ciri-ciri Utama

A copper-tube evaporator with closely spaced aluminum fins provides a large cold surface for water-vapor condensation.

Hot-gas defrost clears evaporator ice during low-temperature operation without relying on a long passive thaw cycle.

A condensate pump lifts collected water to a remote drain where gravity fall is unavailable.

Two-stage fan control and an external humidistat input allow the unit to match changing room moisture loads.

Kebimbangan Produk Pelanggan

Moderately humid rooms need dependable water removal without the regeneration heat and dual air streams required by a desiccant system.

Seasonal humidity repeatedly rises above the acceptable range during production hours.A dedicated refrigeration circuit removes latent load independently of the room cooling thermostat.

The evaporator can ice when inlet air temperature falls during overnight operation.Automatic hot-gas defrost redirects refrigerant heat to the coil and restores airflow quickly.

A full condensate tank stops portable dehumidifiers when no operator is present.A float-controlled pump sends condensate through a hose to the building drain for continuous operation.

Dust accumulation on the cold coil reduces moisture removal and raises energy use.A front-access washable prefilter protects the evaporator and can be removed without opening the refrigeration compartment.

Permohonan yang biasa

Cleanroom support corridors and gowning areasMedical-device packaging roomsPharmaceutical raw-material storesElectronics assembly rooms with moderate dew-point targetsControlled warehouses and archives

Parameter teknikal

Representative construction dimensions for a compact industrial condensation dehumidifier are listed below.

Bahan Teras	Copper-tube aluminum-fin evaporator and condenser with hermetic compressor in a galvanized steel cabinet
Ketebalan Panel	1.0-1.5 mm removable powder-coated cabinet panels
Lebar berkesan	500-900 mm nominal cabinet width
Panjang maksimum	326-547 mm cabinet depth across referenced fixed and portable configurations
Keluli Menghadapi Ketebalan	1.0-1.5 mm galvanized steel exterior sheet
Ketumpatan teras	Approximately 7800-7900 kg/m³ for galvanized carbon-steel cabinet material
Kekonduksian Terma	Approximately 45-55 W/(m·K) for galvanized carbon-steel cabinet material
Kemasan permukaan	White polyester powder coating with a corrosion-resistant blue service panel
Jenis Bersatu	Bolted service cabinet with brazed copper refrigerant joints and hose-connected condensate outlet
Penyesuaian	Boleh didapati berdasarkan aplikasi yang dimaksudkan dan persekitaran operasi.

Pilihan yang boleh didapati

Gravity drain or integrated condensate lifting pumpRemote humidistat and dry-contact alarm connectionDuct collars for closed-loop room recirculationAlternative low-global-warming-potential refrigerant circuit

Planning a Industrial Refrigerant Dehumidifier specification?

Hantarkan kepada kami dimensi anda, syarat pemasangan, sasaran prestasi dan kemasan permukaan yang diperlukan.

Berbincang dengan pasukan kami