Bahasa Inggeris
Bahasa Jerman
Bahasa Arab (Bahasa Melayu)
Bahasa Perancis
Bahasa Indonesia: Bahasa Indonesia
Bahasa Jepun
Bahasa Korea (Bahasa Melayu)
Bahasa Melayu (Bahasa Melayu)Semasa
Bahasa Portugis: Bahasa Portugis: Bahasa Portugis
Bahasa Rusia
Bahasa Sepanyol: Bahasa Sepanyol: Bahasa Sepanyol
Bahasa Melayu (Bahasa Melayu)
Bahasa Turki: Bahasa Turki
Bahasa Vietnam (Bahasa Melayu)
Dinding bilik bersih dan sistem siling
Panel Bilik Bersih Terlindung EPS
A lightweight and economical sandwich panel with an expanded-polystyrene core between coated steel facings, intended for dry general-purpose cleanroom walls and ceilings where moderate insulation and fast installation are required.
- Lightweight EPS Core
- Economical Insulation
- Smooth Steel Surfaces
- Fast Modular Installation
Pengenalan Produk
EPS Insulated Cleanroom Panels use molded expanded-polystyrene blocks bonded between profiled galvanized steel skins. The low-density core keeps panels light and delivers useful thermal separation for general indoor controlled areas. Smooth outer facings create the cleanable surface, while shaped joints align modules and reduce open gaps. EPS is best used where severe heat exposure, aggressive wash-down and high structural loading are not governing requirements. With protected edges and suitable reinforcement around openings, it provides a cost-efficient enclosure for many dry manufacturing and support spaces.
Ciri-ciri Utama
Large modules can be positioned quickly with modest lifting equipment.
Bonded steel skins add surface rigidity and protect the cellular foam core.
Factory-formed joints create predictable alignment across long interior wall runs.
The straightforward panel structure supports economical replacement and room reconfiguration.
Kebimbangan Produk Pelanggan
Correct use depends on protecting the foam, controlling heat exposure, reinforcing fixtures and keeping water out of panel edges.
EPS can be damaged when an exposed edge is struck or abraded.Metal closure profiles protect every perimeter and service opening from direct impact.
A lightweight core does not safely carry heavy wall-mounted equipment by itself.Solid inserts or independent supports transfer concentrated loads away from the foam.
High-temperature areas can exceed the suitable service range of EPS.EPS panels are assigned to ordinary dry interiors while mineral or PIR cores serve higher-risk zones.
Poor joint sealing allows moisture to enter and reduces thermal consistency.Continuous gaskets or sealant close the tongue-and-groove interface along its full length.
Permohonan yang biasa
General electronics assembly roomsDry packaging and inspection areasControlled warehouses and support corridorsTemporary cleanroom partitionsNon-wash-down laboratory support spaces
Parameter teknikal
The following values represent common EPS cleanroom panel manufacturing ranges.
| Bahan Teras | Flame-retardant expanded polystyrene foam |
|---|---|
| Ketebalan Panel | 50, 80, 100, 120, 150 or 200 mm |
| Lebar berkesan | 950, 1050 or 1130 mm |
| Panjang maksimum | 10000 mm |
| Keluli Menghadapi Ketebalan | 0.40 - 0.60 mm |
| Ketumpatan teras | 12.5–20 kg/m³ |
| Kekonduksian Terma | 0.038–0.045 W/(m·K) |
| Kemasan permukaan | Polyester- or food-safe coated galvanized steel |
| Jenis Bersatu | Visible or concealed interlocking joint with sealant |
| Penyesuaian | Terdapat berdasarkan aplikasi yang dimaksudkan dan persekitaran operasi |
Pilihan yang boleh didapati
Food-safe surfaceLocal fixture reinforcementAlternative modular widthCustom dry-area wall and ceiling modules
Planning a EPS Insulated Cleanroom Panel specification?
Hantarkan kepada kami dimensi anda, syarat pemasangan, sasaran prestasi dan kemasan permukaan yang diperlukan.
