Dry room air handling unit with desiccant rotor and regeneration section

클린룸 HVAC 및 공기 처리 장비

건조실 공기 처리 장치

An integrated desiccant air handler that combines deep moisture removal, regeneration, cooling and recirculation for ultra-dry production rooms.

Desiccant Rotor Drying
Low Dew-Point Supply
Separated Regeneration Air
High Recirculation Efficiency

견적 요청 제품 찾아보기

상품 소개

The dry room air handling unit removes water vapor beyond the practical range of cooling coils by passing process air through a continuously regenerated desiccant rotor. A pre-cooling stage reduces incoming moisture load, the rotor performs deep drying, and post-cooling controls supply temperature. A separate heated regeneration airstream removes captured moisture from the rotor and discharges it outdoors. Recirculating most of the dry-room air limits the outdoor moisture load, while sealed casing and low-leakage dampers protect the achieved dew point.

주요 기능

A desiccant rotor removes vapor at dew points where condensation-based cooling becomes inefficient.

Separated process and regeneration air paths prevent wet regeneration exhaust from mixing with dry supply air.

Pre-cooling and sensible post-cooling reduce rotor load and set the final supply temperature.

High dry-air recirculation minimizes the quantity of humid outdoor air that requires deep treatment.

고객 제품 관심사

Ultra-low humidity is easily lost through casing leakage, door infiltration, wet regeneration carryover and moisture released by process materials.

A chilled-water coil cannot reach the required dry-room dew point.The desiccant rotor adsorbs remaining vapor after the air is precooled.

Regeneration exhaust leaks into the dry process airstream.Sealed rotor sectors, pressure control and purge arrangements limit cross-stream carryover.

Opening personnel or material doors causes slow humidity recovery.Sufficient recirculation airflow and controlled dry-air make-up remove the infiltration moisture load.

Reactivation heat dominates system energy use.Purge optimization, heat recovery and the appropriate steam, gas, electric or heat-pump source reduce regeneration demand.

일반적인 응용 프로그램

Lithium-ion battery dry roomsMoisture-sensitive pharmaceutical processingDry powder productionElectronics and component storageResearch-scale ultra-dry laboratories

기술 매개변수

Typical insulated casing construction for an integrated dry-room air handling unit is summarized below.

핵심 재료	Closed-cell polyurethane insulation with silica-gel or molecular-sieve desiccant rotor media
패널 두께	60–100 mm low-leakage insulated casing
유효 폭	1200–4200 mm nominal equipment width
최대 길이	Up to 15000 mm including process and regeneration treatment sections
강철 면면 두께	0.8–1.2 mm coated or stainless casing skins
코어 밀도	40–45 kg/m³ polyurethane panel insulation
열전도도 (Thermal Conductivity)	0.022–0.026 W/(m·K) for casing insulation
표면 마무리	Powder-coated exterior with sealed galvanized or stainless cleanable inner surfaces
접합 유형	Compression-gasketed low-leakage panels with sealed process and regeneration air paths
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

Silica-gel or molecular-sieve rotorSteam, gas, electric or heat-pump regenerationDeep-drying single or multi-stage arrangementHeat recovery and purge-sector optimization

Planning a Dry Room Air Handling Unit specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.