Multi-channel particle monitoring system in three-quarter front view

클린룸 테스트 및 검증 장비

다중 채널 입자 모니터링 시스템

A programmable aerosol manifold system that connects one particle counter to multiple cleanroom sampling locations for economical sequential monitoring.

One counter polls multiple identified sampling points.
Programmable purge and sample steps sequence each line.
Point identities stay linked to monitoring software.

견적 요청 제품 찾아보기

상품 소개

This multi-channel particle monitoring system combines a precision valve manifold, clean sampling paths, sequence controller and compatible airborne particle counter. It automatically selects one location at a time, purges the active line and records the result against the correct point identifier. The architecture is intended for periodic trending across many locations where simultaneous continuous measurement is not required, reducing instrument count without losing a structured sampling plan.

주요 기능

Sequential selection of up to 32 sampling points expands the coverage of one particle counter.

Programmable point order, purge duration and sample time create repeatable unattended monitoring cycles.

Bi-directional control allows the manifold and monitoring software to coordinate point status and timing.

Low-shedding internal flow paths minimize contamination contribution from the switching assembly.

Individual port identification keeps every particle result associated with the correct cleanroom location.

Modular tubing and communication options simplify phased expansion of the monitoring network.

고객 제품 관심사

Sequential monitoring must clear residue from long lines, preserve the identity of each location, and balance purge plus sample time against the required polling cycle.

Long tubing can delay the arrival of a representative sample from a distant point.Programmable purge intervals are assigned by line length so each point is cleared before its measurement begins.

Sequential sampling cannot detect simultaneous short excursions at every location.Use the manifold for periodic trend points and reserve dedicated remote counters for high-risk locations requiring continuous observation.

Incorrect valve mapping can associate data with the wrong room location.Numbered physical ports, locked software point names and commissioning verification establish a traceable channel map.

Particle loss in bends and excessive tubing may bias larger-size channels.Straight conductive tubing routes, controlled lengths and validated transport arrangements minimize avoidable deposition.

일반적인 응용 프로그램

Periodic multi-point particle trending in large cleanroomsElectronics and precision-manufacturing clean-zone monitoringNon-critical support rooms where sequential sampling is acceptableCentralized monitoring of distributed process enclosuresExpansion of an existing facility particle-monitoring network

기술 매개변수

The table defines representative cabinet, port, flow-path, and communication configurations for a multiport switching manifold, with selection based on point count, tubing layout, and particle-counter architecture.

핵심 재료	Powder-coated steel or stainless-steel enclosure with chemically resistant internal valve manifold and clean sampling tubing
패널 두께	Typically 1.0–1.5 mm enclosure panel thickness
유효 폭	Approximately 430–600 mm according to port count and rack configuration
최대 길이	Approximately 450–800 mm for the manifold enclosure; sampling runs may extend to 38100 mm when validated
강철 면면 두께	Typically 1.0–1.5 mm powder-coated or stainless steel
코어 밀도	Not applicable; the equipment enclosure has no insulation core (0 kg/m³)
열전도도 (Thermal Conductivity)	Approximately 14–16 W/(m·K) for stainless steel or 45–60 W/(m·K) for carbon-steel enclosure sections
표면 마무리	Smooth light-gray powder coating or fine-brushed stainless steel with labeled stainless tube ports
접합 유형	Numbered compression-tube sampling ports with Ethernet or serial control interface
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

8, 16, 24 or 32 sampling channelsRack-mount or wall-mount enclosureStainless-steel or powder-coated housingCompatible 28.3 L/min particle counterConductive sampling tubing and point probesFacility monitoring software integration

Planning a Multi-Channel Particle Monitoring System specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.