Three-quarter view of a matched three-piece stainless steel steam humidifier electrode set

クリーンルーム機器のスペアパーツ

加湿器電極

A matched set of large-area stainless steel electrodes for restoring controlled steam generation in a compatible serviceable electrode humidifier cylinder.

Large-Area Stainless Blades
Matched Three-Piece Set
Insulated Plug Terminals
Replaceable Cylinder Component

見積もりリクエスト製品案内

商品紹介

The humidifier electrode is the immersed current-carrying component inside a serviceable electrode steam cylinder. Conductive feedwater completes the electrical path between the stainless steel surfaces, so heat is produced directly in the water rather than by a separate resistance element. Each replacement uses a broad stainless blade joined to rigid support rods, an insulated upper terminal and sealing hardware at the cylinder interface. Electrode length, immersed area, terminal arrangement and set quantity must match the humidifier model because water conductivity and steam demand influence current distribution and normal surface wear.

主要な特徴

Broad stainless steel blade surfaces provide a defined immersed area for conductive steam generation.

Paired support rods maintain the blade position while carrying the terminal assembly above the water space.

A brass retaining shoulder and high-temperature insulating cap separate the electrical connection from the wetted blade.

Matched replacement sets keep electrode geometry and initial active length consistent within the steam cylinder.

お客様の製品に関する懸念事項

Electrode replacement must preserve the original immersed geometry, terminal assignment and cylinder seal while accounting for wear caused by the actual feedwater and steam load.

An electrode with the wrong active length or blade width changes the immersed surface area and operating current.The replacement set is selected by humidifier model, original blade dimensions, terminal position and required cylinder geometry.

Replacing only one heavily worn part can leave unequal electrode lengths and unbalanced current distribution.A complete matched set provides consistent blade geometry and starting length across all three electrode positions.

Incorrect plug assignment can place the supply lead or sensor connection on the wrong terminal.Terminal positions, connector style and identification colors are recorded before removal and reproduced in the replacement arrangement.

Reused or poorly seated sealing rings can allow steam or water to escape around the electrode supports.Compatible new O-rings and retaining hardware are fitted at the cylinder penetrations and checked for even seating during assembly.

典型的な用途

Serviceable electrode steam humidifiersCleanroom AHU humidification sectionsCommercial HVAC steam generatorsElectrode-cylinder maintenance programs

技術的なパラメータ

The following ranges cover common removable large-area stainless steel electrode sets used in serviceable commercial steam humidifier cylinders.

コア材料	Austenitic stainless steel blade and support rods with brass retainer and high-temperature polymer insulator
パネルの厚さ	18-35 mm nominal outside diameter of the upper insulated terminal assembly
有効幅	35-100 mm nominal large-area electrode blade width
最大長さ	80-300 mm selectable initial electrode length for common serviceable cylinder sizes
鋼鉄の厚さを直面する	1.5-3.0 mm nominal stainless steel blade thickness
コア密度	Approximately 7900-8000 kg/m³ for austenitic stainless steel components
熱伝導率	Approximately 14-16 W/(m·K) for austenitic stainless steel near room temperature
表面仕上げ	Clean satin stainless steel blade and rods with warm brass shoulder and matte-black insulating cap
ジョイントタイプ	Welded blade-to-rod construction with retained insulated plug terminal and O-ring cylinder seal
カスタマイズ	意図したアプリケーションと動作環境に基づいて利用できます。

利用可能なオプション

Matched electrode length and blade widthThree-piece replacement setTerminal and plug identification arrangementCompatible hand-nut and O-ring service kit

Planning a Humidifier Electrode specification?

寸法、設置条件、性能目標、必要な表面仕上げをお送りください。

チームに相談する