Three-quarter view of a matched three-piece stainless steel steam humidifier electrode set

클린룸 장비 예비 부품

가습기 전극

A matched set of large-area stainless steel electrodes for restoring controlled steam generation in a compatible serviceable electrode humidifier cylinder.

Large-Area Stainless Blades
Matched Three-Piece Set
Insulated Plug Terminals
Replaceable Cylinder Component

견적 요청 제품 찾아보기

상품 소개

The humidifier electrode is the immersed current-carrying component inside a serviceable electrode steam cylinder. Conductive feedwater completes the electrical path between the stainless steel surfaces, so heat is produced directly in the water rather than by a separate resistance element. Each replacement uses a broad stainless blade joined to rigid support rods, an insulated upper terminal and sealing hardware at the cylinder interface. Electrode length, immersed area, terminal arrangement and set quantity must match the humidifier model because water conductivity and steam demand influence current distribution and normal surface wear.

주요 기능

Broad stainless steel blade surfaces provide a defined immersed area for conductive steam generation.

Paired support rods maintain the blade position while carrying the terminal assembly above the water space.

A brass retaining shoulder and high-temperature insulating cap separate the electrical connection from the wetted blade.

Matched replacement sets keep electrode geometry and initial active length consistent within the steam cylinder.

고객 제품 관심사

Electrode replacement must preserve the original immersed geometry, terminal assignment and cylinder seal while accounting for wear caused by the actual feedwater and steam load.

An electrode with the wrong active length or blade width changes the immersed surface area and operating current.The replacement set is selected by humidifier model, original blade dimensions, terminal position and required cylinder geometry.

Replacing only one heavily worn part can leave unequal electrode lengths and unbalanced current distribution.A complete matched set provides consistent blade geometry and starting length across all three electrode positions.

Incorrect plug assignment can place the supply lead or sensor connection on the wrong terminal.Terminal positions, connector style and identification colors are recorded before removal and reproduced in the replacement arrangement.

Reused or poorly seated sealing rings can allow steam or water to escape around the electrode supports.Compatible new O-rings and retaining hardware are fitted at the cylinder penetrations and checked for even seating during assembly.

일반적인 응용 프로그램

Serviceable electrode steam humidifiersCleanroom AHU humidification sectionsCommercial HVAC steam generatorsElectrode-cylinder maintenance programs

기술 매개변수

The following ranges cover common removable large-area stainless steel electrode sets used in serviceable commercial steam humidifier cylinders.

핵심 재료	Austenitic stainless steel blade and support rods with brass retainer and high-temperature polymer insulator
패널 두께	18-35 mm nominal outside diameter of the upper insulated terminal assembly
유효 폭	35-100 mm nominal large-area electrode blade width
최대 길이	80-300 mm selectable initial electrode length for common serviceable cylinder sizes
강철 면면 두께	1.5-3.0 mm nominal stainless steel blade thickness
코어 밀도	Approximately 7900-8000 kg/m³ for austenitic stainless steel components
열전도도 (Thermal Conductivity)	Approximately 14-16 W/(m·K) for austenitic stainless steel near room temperature
표면 마무리	Clean satin stainless steel blade and rods with warm brass shoulder and matte-black insulating cap
접합 유형	Welded blade-to-rod construction with retained insulated plug terminal and O-ring cylinder seal
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

Matched electrode length and blade widthThree-piece replacement setTerminal and plug identification arrangementCompatible hand-nut and O-ring service kit

Planning a Humidifier Electrode specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.