FFU dan Peralatan Penulenan Udara Terminal

Unit Penapis Kipas Profil Rendah

An ultra-shallow FFU that recesses a flat EC impeller into the plenum to provide final filtration where the ceiling void cannot accept a conventional module.

Approximately 206 mm Housing Depth
Recessed Flat EC Impeller
Reduced Ceiling-Void Requirement
Full-Size Filter Face

Permintaan sebut harga Semak imbas produk

Pengenalan Produk

The low-profile fan filter unit reduces overall height by recessing a broad EC impeller and compact inlet bell into the shallow pressure chamber. The full ceiling footprint is retained, so the final-filter face does not need to shrink with the housing depth. Folded edge channels stiffen the thin casing, and side-mounted electrical access avoids adding equipment above the unit. This construction is intended for renovations, mezzanines and equipment mini-environments where structural beams or services leave little space above the cleanroom ceiling.

Ciri-ciri Utama

A recessed impeller uses the available plan area to minimize the distance between the inlet and filter face.

Folded perimeter channels limit panel vibration without a tall external reinforcing frame.

The side-access controller can be reached within a narrow ceiling void without removing the fan assembly.

A full-area mini-pleat filter preserves a broad low-velocity outlet despite the compact casing.

Kebimbangan Produk Pelanggan

When ceiling height is restricted, the FFU must become shallower without sacrificing filter area, access or uniform outlet velocity.

A conventional 350 mm deep FFU conflicts with cable trays, sprinklers or roof framing above the cleanroom.The recessed fan architecture reduces module depth to approximately 206 mm while retaining the ceiling footprint.

A small high-speed fan fitted into a shallow box creates a concentrated jet and visible diffuser hot spots.A broad low-profile impeller and shallow distribution baffles spread air before it reaches the filter face.

Top-mounted control boxes consume the clearance gained by specifying a shallow FFU.Electrical service hardware is arranged within the side envelope rather than stacked above the inlet.

Thin sheet panels can resonate and transmit fan vibration into the ceiling grid.Folded side rails and elastomeric motor supports stiffen the housing and interrupt vibration paths.

Permohonan yang biasa

Cleanroom retrofits below structural beamsFacilities with congested ceiling servicesLow-headroom laboratory suitesCompact equipment mini-environmentsModular cleanrooms beneath mezzanines

Parameter teknikal

Typical construction ranges for an ultra-shallow low-profile fan filter unit are listed below.

Bahan Teras	Powder-coated steel plenum, recessed backward-curved EC impeller and micro-glass HEPA or ULPA filter pack
Ketebalan Panel	190-260 mm overall module depth; approximately 206 mm is a common compact configuration
Lebar berkesan	532-1132 mm manufactured module width
Panjang maksimum	Up to 1132 mm standard module length
Keluli Menghadapi Ketebalan	0.8-1.0 mm folded galvanized-steel housing sheet
Ketumpatan teras	Approximately 85-115 kg/m³ nominal compacted density of the mini-pleat micro-glass filter pack
Kekonduksian Terma	Approximately 0.035-0.043 W/(m·K) for the shallow mini-pleat pack used in the low-profile FFU
Kemasan permukaan	White epoxy-polyester powder coating with blue-grey reinforced edge channels
Jenis Bersatu	Slim drop-in ceiling flange with continuous gasket and compression-sealed full-area filter frame
Penyesuaian	Boleh didapati berdasarkan aplikasi yang dimaksudkan dan persekitaran operasi.

Pilihan yang boleh didapati

Compact 2 × 2, 2 × 3 or 2 × 4 footprintSide-mounted or remote controllerCompact-depth H14 or U15 filter packRoom-side filter release for shallow ceiling voids

Planning a Low-Profile Fan Filter Unit specification?

Hantarkan kepada kami dimensi anda, syarat pemasangan, sasaran prestasi dan kemasan permukaan yang diperlukan.

Berbincang dengan pasukan kami