FFU 및 터미널 공기 정화 장비

저 프로파일 팬 필터 유닛

An ultra-shallow FFU that recesses a flat EC impeller into the plenum to provide final filtration where the ceiling void cannot accept a conventional module.

Approximately 206 mm Housing Depth
Recessed Flat EC Impeller
Reduced Ceiling-Void Requirement
Full-Size Filter Face

견적 요청 제품 찾아보기

상품 소개

The low-profile fan filter unit reduces overall height by recessing a broad EC impeller and compact inlet bell into the shallow pressure chamber. The full ceiling footprint is retained, so the final-filter face does not need to shrink with the housing depth. Folded edge channels stiffen the thin casing, and side-mounted electrical access avoids adding equipment above the unit. This construction is intended for renovations, mezzanines and equipment mini-environments where structural beams or services leave little space above the cleanroom ceiling.

주요 기능

A recessed impeller uses the available plan area to minimize the distance between the inlet and filter face.

Folded perimeter channels limit panel vibration without a tall external reinforcing frame.

The side-access controller can be reached within a narrow ceiling void without removing the fan assembly.

A full-area mini-pleat filter preserves a broad low-velocity outlet despite the compact casing.

고객 제품 관심사

When ceiling height is restricted, the FFU must become shallower without sacrificing filter area, access or uniform outlet velocity.

A conventional 350 mm deep FFU conflicts with cable trays, sprinklers or roof framing above the cleanroom.The recessed fan architecture reduces module depth to approximately 206 mm while retaining the ceiling footprint.

A small high-speed fan fitted into a shallow box creates a concentrated jet and visible diffuser hot spots.A broad low-profile impeller and shallow distribution baffles spread air before it reaches the filter face.

Top-mounted control boxes consume the clearance gained by specifying a shallow FFU.Electrical service hardware is arranged within the side envelope rather than stacked above the inlet.

Thin sheet panels can resonate and transmit fan vibration into the ceiling grid.Folded side rails and elastomeric motor supports stiffen the housing and interrupt vibration paths.

일반적인 응용 프로그램

Cleanroom retrofits below structural beamsFacilities with congested ceiling servicesLow-headroom laboratory suitesCompact equipment mini-environmentsModular cleanrooms beneath mezzanines

기술 매개변수

Typical construction ranges for an ultra-shallow low-profile fan filter unit are listed below.

핵심 재료	Powder-coated steel plenum, recessed backward-curved EC impeller and micro-glass HEPA or ULPA filter pack
패널 두께	190-260 mm overall module depth; approximately 206 mm is a common compact configuration
유효 폭	532-1132 mm manufactured module width
최대 길이	Up to 1132 mm standard module length
강철 면면 두께	0.8-1.0 mm folded galvanized-steel housing sheet
코어 밀도	Approximately 85-115 kg/m³ nominal compacted density of the mini-pleat micro-glass filter pack
열전도도 (Thermal Conductivity)	Approximately 0.035-0.043 W/(m·K) for the shallow mini-pleat pack used in the low-profile FFU
표면 마무리	White epoxy-polyester powder coating with blue-grey reinforced edge channels
접합 유형	Slim drop-in ceiling flange with continuous gasket and compression-sealed full-area filter frame
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

Compact 2 × 2, 2 × 3 or 2 × 4 footprintSide-mounted or remote controllerCompact-depth H14 or U15 filter packRoom-side filter release for shallow ceiling voids

Planning a Low-Profile Fan Filter Unit specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.