Perabot bilik bersih dan produk keluli tahan karat

Cleanroom Mop Sink

A low-level Type 304 stainless janitorial basin with a coved 16-gauge bowl, removable blue polymer grate, drop-front apron, three-sided splash protection and 76 mm waste.

Low-level bucket access
Coved 16-gauge bowl
Removable blue support grate
Large 76 mm waste

Permintaan sebut harga Semak imbas produk

Pengenalan Produk

The cleanroom mop sink creates a low washing and discharge point for mop heads, buckets and floor-cleaning tools without requiring operators to lift a full pail to bench height. Its Type 304 stainless bowl is formed with generous internal radii and TIG-welded into a three-sided splash enclosure. A shallow drop-front apron shortens the bucket lifting path, while a removable blue polypropylene grate supports pails above the outlet. The flat basket strainer and 76 mm waste handle lint-bearing wash water, and an attached wall clip stabilizes the floor-mounted body.

Ciri-ciri Utama

The low drop-front loading edge reduces the height required to place or empty a filled cleaning bucket.

A removable perforated blue grate holds pails above the waste and lifts out for direct bowl cleaning.

Generous coved corners and blended TIG welds avoid sharp internal intersections around dirty wash water.

Rear and side splash panels contain mop rinse spray without adding a separate wall-mounted upstand.

Kebimbangan Produk Pelanggan

Janitorial teams need to rinse mops and discharge buckets close to floor level without splashing adjacent finishes or blocking a small cleaning room.

Lifting a full bucket into a conventional sink strains the operator and spills wash water.The low floor-mounted bowl and drop-front edge shorten the lifting path.

Mop fibres and debris collect around a small domestic drain.A removable flat basket strainer feeds a 76 mm waste sized for janitorial discharge.

Buckets placed directly over the outlet stop drainage during refilling or rinsing.The raised blue grate supports the bucket while leaving a drainage path beneath it.

Square fabricated corners retain dirty water after the sink is emptied.The sloped bowl floor and large coved radii direct residual water toward the strainer.

Permohonan yang biasa

Cleanroom janitorial closetsControlled corridor cleaning stationsPharmaceutical support washroomsHigh-care food sanitation roomsMedical-device floor-care areas

Parameter teknikal

Typical configurable specifications for a floor-mounted stainless cleanroom mop sink are listed below.

Bahan Teras	Type 304 stainless deep coved basin with removable blue polypropylene bucket grate and stainless basket strainer
Ketebalan Panel	1.5 mm 16-gauge bowl, splash panels and apron
Lebar berkesan	560 mm clear low-level washing width
Panjang maksimum	650 mm maximum front-to-back dimension including rear splash panel
Keluli Menghadapi Ketebalan	1.5 mm Type 304 stainless exposed basin surfaces
Ketumpatan teras	7900-8000 kg / m3 untuk keluli tahan karat Jenis 304
Kekonduksian Terma	14-17 W / (m · K) untuk Keluli tahan karat Jenis 304
Kemasan permukaan	Satin-brushed stainless exterior with smooth coved bowl and blue removable polymer grate
Jenis Bersatu	Fully welded floor basin with rear wall clip, three-sided splash enclosure and 76 mm basket-strainer waste
Penyesuaian	Boleh didapati berdasarkan aplikasi yang dimaksudkan dan persekitaran operasi.

Pilihan yang boleh didapati

Hose bracket and mop hangerWall-mounted swivel mixerType 316 stainless bowlStainless bucket grate

Planning a Cleanroom Mop Sink specification?

Hantarkan kepada kami dimensi anda, syarat pemasangan, sasaran prestasi dan kemasan permukaan yang diperlukan.

Berbincang dengan pasukan kami