Clean steam distribution system three-quarter view with sloped header, three branch drops and support rack

Sistem Utiliti Bilik Bersih

Sistem Pengedaran Steam Bersih

A prefabricated 316L distribution module that routes clean steam through a sloped main, top-fed branches and drained points of use.

Sloped self-draining steam header
Top-fed point-of-use branches
Hygienic condensate removal

Permintaan sebut harga Semak imbas produk

Pengenalan Produk

The Clean Steam Distribution System begins at the clean-steam source outlet and delivers steam to separated hygienic users without adding another generation stage. Its 316L main header is arranged with a continuous fall toward a drain pocket, while branch take-offs rise from the top of the main before descending to point-of-use valves. A clean-steam trap removes collected condensate at the terminal low point, and local pressure instruments provide operating visibility. Prefabricated supported sections reduce field joints while retaining the drainage, support and thermal-movement allowances required by the final route.

Ciri-ciri Utama

316L stainless-steel main and branches

Continuous header fall toward drainage

Three top-entry point-of-use take-offs

Drainable hygienic valve orientation

Orbital-welded primary tube joints

Terminal drain pocket and clean-steam trap

Local pressure indication and transmission

Prefabricated rack with defined pipe supports

Kebimbangan Produk Pelanggan

A downstream clean-steam network must deliver dry, usable steam while continuously removing condensate and avoiding stagnant pockets across several intermittent users.

Condensate pools in a level header and can initiate water hammerInstall the main with a controlled fall toward a full-bore drain pocket and discharge through a correctly selected clean-steam trap.

Side or bottom take-offs carry wet steam into critical usersLift each branch from the top of the main before turning down to its point-of-use isolation valve.

Excess removable joints and dead legs complicate hygienic maintenanceUse orbital butt welds through the fixed runs and reserve hygienic clamps for components that require removal or inspection.

Thermal growth and changing demand strain pipework or starve remote usersSize each header and branch from the load profile, then coordinate guided supports and expansion allowance with the final route.

Permohonan yang biasa

Autoclave and washer-sterilizer supplyBioreactor and process-vessel SIPAseptic filling-line steam barriersFood and beverage direct-steam servicesClean humidification distribution

Parameter teknikal

Header diameter, branch size, steam pressure, drainage spacing, insulation, trap duty, support pitch and modular section length are selected from the connected load schedule and installed routing.

Bahan Teras	316L stainless steel hygienic main header, branches, drain pocket and condensate discharge path
Ketebalan Panel	Sanitary tube wall typically 0.89–2.77 mm
Lebar berkesan	Main and branch outside diameters typically 25.4–101.6 mm
Panjang maksimum	Prefabricated supported module length typically up to 6000 mm
Keluli Menghadapi Ketebalan	Instrument and support plates typically 1.5–3.0 mm
Ketumpatan teras	316L stainless steel density approximately 8000 kg/m³
Kekonduksian Terma	316L stainless steel approximately 15 W/(m·K) at ambient temperature
Kemasan permukaan	Passivated 316L tubing with project-selected mechanically polished or electropolished internal finish
Jenis Bersatu	Orbital butt-welded fixed runs with hygienic clamp joints at removable valves, trap and instruments
Penyesuaian	Boleh didapati berdasarkan aplikasi yang dimaksudkan dan persekitaran operasi.

Pilihan yang boleh didapati

Header and branch diameter selectionPolished or electropolished internal finishInsulation with stainless protective claddingManual or actuated point-of-use valvesThermostatic or mechanical clean-steam trapSeparator and air-vent connection provisionsPressure and temperature monitoring pointsCondensate return or safe-discharge interface

Planning a Clean Steam Distribution System specification?

Hantarkan kepada kami dimensi anda, syarat pemasangan, sasaran prestasi dan kemasan permukaan yang diperlukan.

Berbincang dengan pasukan kami