Wall-mounted knee-operated stainless hand washing sink

클린룸 가구 및 스테인레스 스틸 제품

스테인레스 스틸 손 세척 싱크대

A compact wall-mounted Type 304 stainless basin with a mechanical knee push panel, coved rectangular bowl, sloped backsplash, premixing valve and 40 mm waste outlet.

Mechanical knee water control
Coved single-piece basin
30-degree sloped backsplash
Accessible plumbing shroud

견적 요청 제품 찾아보기

상품 소개

This stainless steel hand washing sink uses a broad front knee panel to actuate the concealed mechanical water valve, leaving both hands free throughout washing. The 460 mm-wide Type 304 basin has radiused internal corners, an integral tap ledge and a 30-degree sloped backsplash that drains splashes toward the bowl. A preset hot/cold premixing valve supplies the fixed stainless spout, while a removable lower shroud protects the valve, hoses and 40 mm drain without sealing them into an inaccessible cabinet.

주요 기능

A full-width knee panel opens the mechanical valve without electrical power or hand contact at the basin.

The coved rectangular bowl and welded drain transition remove sharp internal intersections around standing water.

The backward-sloped backsplash returns spray toward the bowl rather than forming a horizontal ledge.

A removable stainless shroud conceals plumbing while retaining direct service access to the mixer and valve linkage.

고객 제품 관심사

Entry hand washing needs reliable hands-free water control, a compact wall footprint and serviceable plumbing without introducing electronic components into every station.

Operators touch a faucet handle immediately after soaping their hands.The broad knee panel controls the valve while both hands remain over the bowl.

Flat splashbacks retain droplets behind the spout and mixer area.The 30-degree rear panel slopes continuously back toward the coved basin.

Square bowl seams and separate tap decks trap residue around their junctions.A formed one-piece bowl and integral tap ledge use welded radiused transitions.

Fully enclosed cabinets make mechanical valve and drain maintenance slow.The front shroud removes independently to expose the linkage, mixer and 40 mm waste.

일반적인 응용 프로그램

Cleanroom personnel entrance hand washingFood high-care hygiene stationsPharmaceutical support laboratoriesMedical-device production wash pointsControlled packaging room access

기술 매개변수

Typical configurable specifications for a compact knee-operated stainless hand washing sink are listed below.

핵심 재료	Type 304 stainless coved bowl, sloped backsplash, knee panel, mechanical valve, premixer and removable plumbing shroud
패널 두께	1.2 mm formed basin, splashback and front shroud
유효 폭	460 mm overall single-station width
최대 길이	524 mm maximum overall height including backsplash
강철 면면 두께	1.2 mm Type 304 stainless exposed sheet surfaces
코어 밀도	7900 - 8000 kg / m 3 Type 304 스테인레스 스틸
열전도도 (Thermal Conductivity)	14 - 17 W / (m · K) 유형 304 스테인레스 스틸
표면 마무리	Uniform #4 satin-brushed exterior with smooth coved bowl and passivated welds
접합 유형	Wall hanger bracket with sealed backsplash, knee-linked mechanical valve, flexible inlet unions and 40 mm welded waste
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

Cold-water-only valveTimed mechanical shutoffIntegrated soap dispenserFloor-standing pedestal frame

Planning a Stainless Steel Hand Washing Sink specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.