Three-quarter view of slim low-resistance HEPA filter with mini-pleat face

공기 필터 및 화학 여과

저저항 HEPA 필터

An optimized mini-pleat HEPA panel that combines fine glass-microfibre media with uniform pleat channels to reduce fan resistance at cleanroom operating airflow.

Optimized Pleat Geometry
Reduced Fan Resistance
Uniform Air Distribution
Slim Aluminium Frame

견적 요청 제품 찾아보기

상품 소개

The low-resistance HEPA filter is built around a closely controlled mini-pleat pack with precisely spaced hot-melt beads. Greater effective media area and uniform channel depth reduce local velocity peaks that add pressure loss. The pack is sealed into an anodized-aluminium frame with polyurethane and protected by a lightweight expanded-metal faceguard. Gasket, gel and knife-edge versions fit common terminal housings, fan filter units and low-energy air-handling systems where stable HEPA performance must be achieved with a limited fan-pressure budget.

주요 기능

Optimized pleat height and spacing increase usable media area without restricting the discharge face.

Even hot-melt separators reduce turbulent flow and prevent pleat crowding at operating pressure.

A slim anodized-aluminium frame limits weight while maintaining cleanroom-compatible surfaces.

Multiple perimeter-seal formats allow the same low-resistance media concept to fit ceiling or AHU housings.

고객 제품 관심사

A cleanroom may meet particle targets yet consume unnecessary energy if the final filter imposes avoidable resistance throughout its service life.

Existing FFU motors run near maximum speed to overcome the terminal filter.The expanded mini-pleat area lowers media velocity and preserves more usable fan-pressure reserve.

Uneven pleat spacing produces early loading in isolated sections of the filter.Consistent separator placement distributes airflow and particulate capture across the whole face.

A bulky deep filter will not fit the available ceiling plenum.The shallow aluminium-frame panel provides HEPA filtration in common 69–90 mm terminal depths.

Reducing pressure drop must not create a fragile media pack.Faceguards, continuous edge potting and controlled pleat geometry support the pack during handling and operation.

일반적인 응용 프로그램

Energy-efficient fan filter unitsLow-pressure cleanroom ceilingsSemiconductor process bays의약품 충전 제품군Clean laboratory supply terminals

기술 매개변수

Typical low-resistance mini-pleat HEPA panel ranges are listed below.

핵심 재료	High-area glass-microfibre HEPA media with thermoplastic mini-pleat separators
패널 두께	69–90 mm aluminium-frame depth
유효 폭	305 - 610 mm 공칭 면 너비
최대 길이	최대 1220 mm 공칭 면 길이
강철 면면 두께	0.4–0.6 mm galvanized or powder-coated expanded-steel faceguard
코어 밀도	Approximately 30–45 kg/m³ equivalent mini-pleat media density
열전도도 (Thermal Conductivity)	Approximately 0.035–0.043 W/(m·K) for the dry glass-microfibre pack
표면 마무리	Natural anodized-aluminium frame with clean white or galvanized faceguards
접합 유형	EPDM gasket, polyurethane gel channel or extruded knife-edge frame
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

H13 or H14 efficiency69 mm or 90 mm frame depthDry gasket or fluid-gel sealPowder-coated or stainless-steel faceguard

Planning a Low-Resistance HEPA Filter specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.