Three-quarter view of a complete AHU deep-groove bearing with separated rubber seal

클린룸 장비 예비 부품

AHU 베어링

A precision deep-groove ball bearing with optional contact seals for supporting matched AHU motor or blower shafts under radial and moderate axial loads.

Deep-Groove Raceway
Precision Steel Balls
Optional Contact Seals
Matched Shaft Fit

견적 요청 제품 찾아보기

상품 소개

The AHU bearing is a single-row deep-groove rolling bearing selected for compatible fan motors, blower shafts or bearing cartridges. Hardened steel inner and outer rings contain one row of precision balls separated by a cage, while optional elastomer seals retain lubricant and restrict contaminant entry. The deep raceways support radial load and moderate axial load in either direction, making this construction common in rotating air-moving equipment. Replacement selection must match the original bore, outside diameter, width, internal clearance, closure arrangement, speed and fit rather than using shaft diameter as the only criterion.

주요 기능

Deep raceway grooves guide a single ball row and accommodate combined radial and moderate bidirectional axial loading.

Precision-ground rings and uniformly spaced balls support stable rotation when the shaft and housing seats are correctly aligned.

Removable or factory-installed elastomer seals help retain grease and limit dust ingress in enclosed AHU service positions.

Standardized boundary dimensions simplify interchange when the complete bearing designation and clearance suffix are verified.

고객 제품 관심사

Bearing life depends on matching dimensions and internal design while preventing damage during storage, mounting, lubrication and shaft alignment.

The same bore size is available in several outside diameters, widths, clearances and closure styles.The complete designation and measured bore, outer diameter and width are checked before an interchange is selected.

An overly tight fit or impact through the wrong ring can brinell the raceway before the fan returns to service.Mounting force is applied only to the ring being fitted, using controlled tooling and the specified shaft and housing tolerances.

Open, shielded and contact-sealed bearings differ in grease retention, friction and contamination protection.The closure and lubricant arrangement are selected for the installed speed, access and cleanliness conditions.

Shaft misalignment or fan imbalance produces vibration and uneven bearing loading.The replacement is combined with shaft-seat inspection, alignment checks and verification of the rotating fan assembly.

일반적인 응용 프로그램

AHU fan motor shaftsBelt-driven blower bearing cartridgesCleanroom exhaust fan assembliesVentilation equipment overhaul

기술 매개변수

Typical construction and boundary ranges for compact single-row AHU deep-groove ball bearings are listed below.

핵심 재료	Through-hardened chromium bearing-steel rings and balls with steel cage and optional NBR seals
패널 두께	8-35 mm nominal bearing width
유효 폭	10-80 mm nominal shaft bore
최대 길이	Up to 170 mm nominal outside diameter for common AHU selections
강철 면면 두께	2-18 mm radial ring section, dependent on bearing series
코어 밀도	Approximately 7810-7850 kg/m³ for chromium bearing steel
열전도도 (Thermal Conductivity)	Approximately 42-46 W/(m·K) for hardened bearing steel
표면 마무리	Precision-ground silver race surfaces with preserved steel or dark NBR closure faces
접합 유형	Single-row deep-groove rolling contact with press-fit inner and outer ring seats
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

Open, shielded or contact-sealed closureNormal or increased internal clearanceAlternative cage materialMatched bore and boundary series

Planning a AHU Bearing specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.