Englisch
DeutschCurrent
Arabisch
Französisch
indonesisch
Japanisch
Koreanisch
Malaiisch
Portugiesisch
Russisch
Spanisch
Thailändisch
Türkischer Sprache
Vietnamesisch
Cleanroom Installation Zubehör
HEPA-Filter - Testport
A room-side stainless bulkhead test port with a quick coupling, tethered cap and rear hose barb for controlled pressure or aerosol sampling at HEPA housings.
- Room-Side Quick Connection
- Tethered Metal Dust Cap
- Threaded Bulkhead Mount
- Barbed Tubing Interface
Produkteinführung
The HEPA filter test port combines a machined stainless quick-coupling socket with a two-hole face flange, threaded bulkhead, hex locknut and rear hose barb. Installed through a terminal housing or test-panel wall, it creates a defined connection between room-side test equipment and the intended pressure or aerosol line. The separate knurled cap remains attached by a short chain, protecting the exposed socket between validation activities without becoming a loose service item.
Key Features
A broad circular flange with two countersunk holes stabilizes the fitting against the housing face.
The rear male thread and hex locknut clamp the bulkhead securely through a prepared panel opening.
A stepped hose barb supports a direct transition to a correctly sized flexible sampling or injection line.
The knurled protective cap stays captured by a stainless chain during testing and servicing.
Kunden Produktbedenken
HEPA validation connections must remain accessible for instruments while preserving a secure, cleanable interface between test cycles.
Reaching an upstream plenum directly can require grille removal or awkward access above the cleanroom ceiling.The bulkhead fitting places a dedicated quick connection at the accessible room-side face.
An exposed socket can collect residue or become an unintended leakage path between test cycles.The close-fitting knurled cap protects the interface and remains captured by its short tether chain.
A poorly matched flexible tube can slip from the fitting or restrict the test flow path.The stepped rear barb is selected to suit the test-line bore and provides multiple retention lands.
A single-point fitting may rotate or leak where it passes through a thin housing wall.The two-hole flange resists rotation while the threaded bulkhead and locknut maintain controlled panel compression.
Typische Anwendungen
Upstream aerosol concentration sampling at terminal HEPA housingsDownstream sampling circuits for exhaust-filter test fixturesStatic-pressure measurement at cleanroom filter plenumsChallenge-aerosol connection points in compatible validation arrangementsRoom-side access for ceiling and wall HEPA filter testing
Technische Parameter
Typical material and dimensional ranges for a stainless bulkhead HEPA filter test port are listed below.
| Core Material | Machined 304 or optional 316L stainless-steel flange, coupling, bulkhead, locknut, hose barb and tethered cap |
|---|---|
| Panel Dicke | 0.8-3.0 mm compatible HEPA housing or test-panel wall thickness |
| Effektive Breite | 6-12 mm nominal test-line bore or compatible hose inside diameter |
| Maximale Länge | Up to 120 mm overall bulkhead and hose-barb length |
| Stahl facing Dicke | 2.0-5.0 mm nominal circular mounting-flange thickness |
| Kerndichte | Approximately 7900-8000 kg/m³ for austenitic stainless steel |
| Thermische Leitfähigkeit | Approximately 14-17 W/(m·K) for austenitic stainless steel |
| Oberfläche Finish | Brushed, satin-machined or passivated natural stainless-steel finish |
| Gemeinsamer Typ | Two-hole face flange with thread-locked bulkhead, front quick coupling and rear barbed tube connection |
| Customisierung | Verfügbar je nach beabsichtigter Anwendung und Betriebsumgebung. |
Verfügbare Optionen
304 or 316L stainless-steel constructionQuick-coupling and hose-barb sizes matched to test tubingEPDM or silicone flange gasketCustom two-hole flange pattern and bulkhead lengthStraight or elbow rear tube connection
Planning a HEPA Filter Test Port specification?
Senden Sie uns Ihre Abmessungen, Installationsbedingungen, Leistungsziele und gewünschte Oberflächenveredelung.
