Three-quarter view of an EPDM-lined cleanroom pipe support and hanger

클린룸 설치 액세서리

파이프 지지 및 걸러

A galvanized split-ring pipe hanger with an EPDM liner, threaded suspension rod and ceiling plate for supporting cleanroom utility pipework.

EPDM-Lined Split Ring
Threaded Drop Adjustment
Two-Bolt Clamp Closure
Galvanized Steel Hardware

견적 요청 제품 찾아보기

상품 소개

This suspended support combines a two-piece circular clamp, resilient liner and adjustable threaded drop in one compact assembly. The liner separates the pipe from the steel band and cushions minor vibration, while the two side fasteners open the ring for installation around completed pipe runs. A locknut secures the selected drop height beneath the two-hole ceiling plate.

주요 기능

The split-ring construction opens around installed pipe without feeding the pipe through a closed loop.

A continuous black EPDM liner cushions the pipe surface and limits direct metal-to-pipe contact.

The centered threaded rod provides practical vertical adjustment during utility alignment.

Two opposed closing bolts distribute clamping force around the circular band.

The compact top plate provides two clearly separated structural attachment points.

고객 제품 관심사

Cleanroom utility lines need adjustable overhead support that protects the pipe surface, avoids unstable point contact and remains accessible during alignment.

Rigid bare-metal bands can mark coated pipe and transmit vibration into the support structure.The continuous EPDM liner creates a resilient separation layer between the pipe and galvanized clamp.

A fixed suspension length makes it difficult to maintain pipe slope beneath uneven structure.The threaded rod and locknut allow the clamp elevation to be adjusted before final tightening.

Closed-loop hangers are awkward to add after a utility run has been assembled.The two-piece ring opens at its side fasteners so it can be fitted around an existing line.

Single-point ceiling attachments can rotate while installers align the pipe run.The two-hole anchor plate provides a stable structural interface above the centered hanger rod.

일반적인 응용 프로그램

Cleanroom process-water pipe suspensionCompressed-air and inert-gas utility linesLow-temperature drain and condensate pipingService-plenum tubing supportPharmaceutical and electronics facility utility routing

기술 매개변수

Typical material and dimensional ranges for an adjustable lined cleanroom pipe support and hanger are listed below.

핵심 재료	Zinc-plated carbon-steel split ring, threaded rod and ceiling plate with black EPDM liner
패널 두께	2.0-3.0 mm nominal split-ring band thickness
유효 폭	15-200 mm nominal supported pipe outside diameter
최대 길이	Up to 1500 mm adjustable threaded suspension drop
강철 면면 두께	3.0-5.0 mm nominal ceiling plate thickness
코어 밀도	Approximately 7850 kg/m³ for carbon-steel components
열전도도 (Thermal Conductivity)	Approximately 45-60 W/(m·K) for carbon steel
표면 마무리	Silver electro-galvanized steel with matte black EPDM contact lining
접합 유형	Two-bolt lined split ring connected to a locknut-adjusted threaded suspension rod
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

M8, M10 or M12 suspension rodElectro-galvanized, hot-dip galvanized or stainless-steel hardwareEPDM or silicone liner selectionClamp diameters matched to the utility pipe outside diameterCustom ceiling plate and suspension drop length

Planning a Pipe Support and Hanger specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.