Three-quarter overhead view of a modular FFU ceiling grid with four blue inlet fan filter units

FFU 및 터미널 공기 정화 장비

FFU 천장 그리드 시스템

A sealed modular T-grid structure that coordinates FFUs, lights, blank panels and service modules while transferring their loads to wall supports or suspension rods.

Modular FFU Bays
Factory-Applied Gaskets
Integrated Utility Support
Replaceable Grid Components

견적 요청 제품 찾아보기

상품 소개

The FFU ceiling grid system uses interlocking aluminium or stainless profiles to create repeatable bays for fan filter units, LED panels, blank tiles and utility penetrations. Factory-applied closed-cell gaskets seal the underside contact line, while splice clips, corner keys and hanger points maintain alignment across the ceiling field. Standard module pitches accept common FFU formats, and partial bays can be fitted with sealed infill panels. The system provides a coordinated structural and sealing interface; it does not replace the independent building structure required to carry the calculated ceiling loads.

주요 기능

Repeatable metric or 2 × 4 ft bays allow FFUs and lights to exchange positions during a layout revision.

Continuous closed-cell gasketing limits bypass paths between the grid and drop-in components.

Interlocking splice hardware keeps exposed ceiling lines straight without bulky room-side fasteners.

Dedicated suspension and perimeter members separate component loading from cleanroom wall panels.

고객 제품 관심사

A dense FFU ceiling must remain sealed and visually aligned while carrying many service modules and still permitting future reconfiguration.

Small dimensional errors accumulate across a large ceiling and prevent FFUs from dropping into their bays.Factory-sized main runners, cross tees and positive splice keys hold a repeatable module pitch.

Air leaks through hard contacts between filters, lights and bare T-bar flanges.A continuous closed-cell gasket creates a compressible seal beneath each drop-in component.

Replacing one FFU requires dismantling neighbouring ceiling sections.Independent bays and removable hold-down hardware allow a single module to be lifted or lowered.

Uncoordinated lights and service penetrations overload isolated grid members.Load paths, suspension points and utility bays are arranged within one ceiling support layout.

일반적인 응용 프로그램

Semiconductor ballroom ceilingsModular pharmaceutical cleanrooms의료기기 생산 제품군Aerospace assembly clean zonesResearch laboratory cleanrooms

기술 매개변수

Typical material and module ranges for a gasketed FFU ceiling grid system are shown below.

핵심 재료	6063-T5 aluminium T-grid profiles with steel suspension rods and closed-cell PE or EPDM gaskets
패널 두께	38-75 mm nominal grid web depth
유효 폭	600-1200 mm standard module pitch with metric or imperial bay layouts
최대 길이	Up to 6000 mm continuous primary runner length before a mechanical splice
강철 면면 두께	1.0-2.0 mm galvanized steel support plates or stainless component trays where fitted
코어 밀도	30-80 kg/m³ nominal density of the closed-cell perimeter gasket
열전도도 (Thermal Conductivity)	0.035-0.060 W/(m·K) for the closed-cell grid sealing gasket
표면 마무리	Cleanroom-white powder-coated aluminium, clear anodized aluminium or brushed 304 stainless steel
접합 유형	Interlocking T-bar splice clips and corner keys with gasketed drop-in module seats
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

600 × 600 or 600 × 1200 mm baysWall-supported or rod-suspended layoutPowder-coated aluminium or stainless finishFFU, light, blank panel and utility modules

Planning a FFU Ceiling Grid System specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.