Three-quarter view of a flat 100 mm aluminium cleanroom skirting fascia and concealed rear clip rail

클린룸 설치 액세서리

클린룸 스커트

A 100 mm flat-faced anodized aluminium base profile with a separate concealed rear clip rail for a clean, screw-free finish at the lower edge of cleanroom walls.

100 mm Flat Face
Concealed Rear Clip Rail
Matte Anodized Aluminium
Up to 3000 mm Length

견적 요청 제품 찾아보기

상품 소개

This cleanroom skirting uses a straight extruded aluminium fascia rather than a concave radius. The 100 mm visible face covers the lower wall edge, while narrow top and bottom returns stiffen the section without turning it into a coving profile. A dedicated aluminium carrier remains behind the fascia after installation, allowing the exposed cover to clip into place with no screw heads interrupting the front surface. Natural matte anodizing provides a restrained silver finish suited to modular cleanroom partitions, laboratory corridors and other controlled interiors.

주요 기능

The broad planar face protects and finishes the low wall zone without introducing the sweeping internal radius used by cleanroom coving.

A separate continuous rear rail receives the fascia and keeps the mechanical attachment concealed after clipping.

One narrow return at each longitudinal edge reinforces the extrusion and gives the exposed top and floor lines a crisp termination.

A 100 mm visible height provides practical coverage at the wall base while retaining a compact projection into the room.

Matte natural anodizing controls glare, preserves clear aluminium midtones and supports routine wipe-down of the accessible surface.

고객 제품 관심사

The bottom edge of a partition is exposed to cleaning contact, small trolley scuffs and visual gaps where the wall meets the finished floor.

Visible screws and fixing recesses along the wall base can interrupt a simple cleaning pass.The rear clip rail carries the fascia while leaving the entire exposed aluminium face free of screw heads.

A thin decorative trim may not cover the low wall zone where mops, footwear and light equipment make frequent contact.The 100 mm-high face gives the lower wall a continuous protective finish without the bulk of an impact bumper.

Profiles intended for radius corners can be mistaken for a flat base finish and create an unwanted curved transition.This assembly retains a planar front with only narrow straight returns, clearly separating its skirting function from floor coving.

Long wall runs can look uneven when several exposed fastening methods or mismatched surface finishes are combined.Straight extruded lengths and a concealed continuous carrier establish a consistent silver base line across the partition run.

일반적인 응용 프로그램

Modular cleanroom partition basesPharmaceutical and biotechnology support corridorsMedical-device manufacturing roomsControlled laboratory circulation areasHygienic production and packaging interiors

기술 매개변수

The following values describe the selected 100 mm matte-anodized aluminium fascia and rear-clip configuration.

핵심 재료	Extruded EN AW-6063 aluminium fascia with a matching aluminium rear clip rail
패널 두께	1.6 mm nominal extrusion wall thickness
유효 폭	100 mm visible skirting height
최대 길이	Up to 3000 mm per continuous profile
강철 면면 두께	0 mm; the selected configuration has no steel facing
코어 밀도	Approximately 2700 kg/m³ for the aluminium extrusion
열전도도 (Thermal Conductivity)	Approximately 190-200 W/(m·K) at 20°C
표면 마무리	Natural silver matte anodized aluminium with a smooth wipeable face
접합 유형	Concealed continuous rear-clip engagement with straight butt joints between adjacent lengths
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

Factory-cut profile lengths below the 3000 mm maximumWhite powder-coated finish for matching cleanroom wall panelsAlternative 85 mm or 90 mm visible heightsMatching left and right end piecesMatching internal and external corner accessories

Planning a Cleanroom Skirting specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.