Three-quarter view of a stainless Venturi airflow control valve with actuator

クリーンルーム空気分配システム

Venturi 空気の流れ制御弁

A characterized stainless Venturi valve whose spring-compensated cone preserves the commanded airflow as duct static pressure varies.

Pressure-Independent Flow Response
Spring-Compensated Venturi Cone
Fast Commanded Repositioning
Corrosion-Resistant Air Path

見積もりリクエスト製品案内

商品紹介

The Venturi airflow control valve uses a shaped throat and movable cone to create a repeatable relationship between cone position and airflow. A mechanical spring shifts the cone in response to duct-pressure change, while the actuator establishes the opening required by the control command. Because pressure compensation occurs inside the valve body, the controller can respond without continuously deriving airflow from a separate duct sensor. Stainless wetted components and an external actuator make the assembly suitable for supply, general exhaust and laboratory exhaust duties.

主要な特徴

A calibrated Venturi throat and cone produce a stable position-to-airflow characteristic over the operating range.

Mechanical spring compensation reacts directly to static-pressure variation before the room-pressure loop drifts.

A fast external actuator supports fume-hood tracking and rapid room supply-to-exhaust balance changes.

Smooth stainless internal surfaces and external drive components reduce residue traps in demanding exhaust service.

お客様の製品に関する懸念事項

Critical-room airflow control must remain repeatable through duct-pressure swings, react quickly to demand and tolerate contaminants without a drifting measurement element.

A fan-speed change alters several branch flows before the room pressure loop can recover.The spring-loaded cone compensates mechanically for the duct-pressure change at each valve.

Fume-hood sash movement requires a large exhaust change within seconds.A characterized cone and fast actuator move directly to the airflow position commanded by the hood controller.

Dust or chemical residue blocks small pressure-sensor ports in an exhaust branch.The pressure-independent cone mechanism controls flow without small in-stream averaging taps.

Mismatched supply and exhaust response reverses the intended room pressure direction.Coordinated valve commands and known flow-position curves maintain the scheduled offset between room air paths.

典型的な用途

Pharmaceutical room pressure controlLaboratory fume-hood exhaustCleanroom supply and return trackingAnimal research ventilationHealthcare isolation-room airflow

技術的なパラメータ

Representative construction ranges for a stainless Venturi airflow control valve are shown below.

コア材料	304 or 316 stainless-steel Venturi body with spring-compensated cone and stainless linkage
パネルの厚さ	1.0–1.5 mm formed Venturi body wall
有効幅	152–356 mm nominal round duct diameter
最大長さ	Up to 1200 mm overall body length including transition sections
鋼鉄の厚さを直面する	1.2–2.0 mm stainless mounting flange and actuator support plates
コア密度	Approximately 8000 kg/m³ for 304 or 316 stainless-steel airflow components
熱伝導率	14–16 W/(m·K) through the 304 or 316 stainless Venturi body at room temperature
表面仕上げ	Smooth mill-finish or passivated stainless air path with protected external actuator
ジョイントタイプ	Round flanged or slip-fit Venturi body with guided cone shaft and external direct-coupled linkage
カスタマイズ	意図したアプリケーションと動作環境に基づいて利用できます。

利用可能なオプション

Constant-volume or variable-volume controlSupply, general exhaust or coated corrosive-exhaust constructionAnalog or BACnet-compatible controllerFail-safe actuator and position feedback

Planning a Venturi Airflow Control Valve specification?

寸法、設置条件、性能目標、必要な表面仕上げをお送りください。

チームに相談する