Vacuum exhaust HEPA filter front-right three-quarter view with one dark housing, two pipe ports, pressure taps, drain and two-foot base

클린룸 유틸리티 시스템

진공 배기 HEPA 필터

A remotely piped HEPA-grade discharge unit that captures fine particulate released by a compatible dry vacuum pump before the exhaust reaches a room or facility duct, while providing serviceable pressure taps, condensate drainage and a stable mounting base.

Downstream dry-pump exhaust filtration
99.99% particulate efficiency at 0.3 µm family basis
Full-vacuum housing with 90°C temperature limit

견적 요청 제품 찾아보기

상품 소개

The Vacuum Exhaust HEPA Filter is a complete pump-discharge assembly for clean utilities, laboratories and controlled production areas where dry-scroll tip-seal dust or other fine particles must not be released directly into the occupied space. The locked configuration uses one vertical full-vacuum housing with a single pleated borosilicate microglass cartridge, separate low and high pipe connections, two differential-pressure take-off ports, a low-point drain and a two-foot base. Its flow path is downstream of the pump, so it differs fundamentally from a sanitary vacuum-line sterile filter installed on the suction side. The unit is not an oil-vapour adsorber, does not replace source-specific gas treatment and should be preceded by a suitable coalescing separator when a lubricated pump produces significant oil mist.

주요 기능

A HEPA-grade borosilicate microglass cartridge provides a defined final particulate barrier for compatible dry-pump discharge

Full-vacuum-capable housing construction tolerates reverse pressure conditions that may occur during shutdown or abnormal line sequencing

A 90°C housing-family temperature boundary accommodates warm discharge from correctly selected dry vacuum pumps

Separate lower inlet and upper outlet connections support a vertical upward flow path and remote exhaust piping

Two capped pressure take-offs allow clean and loaded differential pressure to be measured without a permanently mounted gauge

The low-point drain provides a controlled way to remove incidental condensate after the unit is isolated and depressurized

A removable top cover and circumferential clamp band give direct access to the single replaceable cartridge

The saddle base with two mounting feet transfers pipe and service loads to the floor or skid instead of the filter connections

고객 제품 관심사

Reliable pump-exhaust filtration depends on the pump technology, maximum discharge temperature, gas chemistry, pressure pulsation, condensate load, pipe backpressure and the acceptable terminal pressure drop.

Dry-scroll tip-seal dust can be discharged into a clean technical room even when the process suction line is already filteredPlace the HEPA unit after the pump and before the room outlet or facility exhaust connection so pump-generated particles encounter the final cartridge.

A small exhaust element can raise backpressure, increase pump temperature and reduce evacuation performance as it loadsSize the cartridge and pipe connections from the pump's free-air displacement, allowable exhaust backpressure and clean-to-change differential-pressure limit.

Warm discharge or process vapour can damage media, seals or a plastic filter bowlVerify the worst-case exhaust temperature and gas compatibility against the 90°C housing-family boundary and select a lower upstream cooling or treatment stage when required.

Condensate collecting at the bottom of a vertical exhaust housing can wet the HEPA pack and sharply increase resistanceKeep the unit upright, slope connecting pipework appropriately and drain the isolated low point before liquid reaches the filter media.

An exhaust filter may see reverse vacuum during pump shutdown or valve sequencingUse a documented full-vacuum housing and confirm the closure, flanges, drain and pressure-port blanks share the required bidirectional pressure boundary.

HEPA, oil-mist coalescing and vapour adsorption are often treated as interchangeable exhaust controlsDefine the contaminant first: use this HEPA stage for particles, add a coalescer for lubricant aerosol and add compatible adsorption or catalytic treatment for gases and vapours.

일반적인 응용 프로그램

Dry scroll vacuum pump exhaust serving cleanroom production equipmentLaboratory vacuum systems that must prevent pump-generated particles from entering occupied roomsLyophilizer and chamber evacuation skids with compatible dry-pump dischargeSemiconductor and precision-process vacuum utilities handling non-corrosive particulate exhaustMedical and research equipment requiring a remotely piped final particulate barrier after the pumpClean utility packages that monitor exhaust-filter differential pressure and planned element replacement

기술 매개변수

The catalogue-scale basis is one vertical Walker T-Series-class housing in a dry-pump exhaust particulate configuration. The conservative housing-family limits are full vacuum to 0.5 barg and 90°C. One borosilicate microglass cartridge is selected for 99.99% particulate efficiency at 0.3 µm, with an FKM seal, a lower inlet, upper outlet, two differential-pressure take-offs, low-point drain, removable cover clamp and two-foot support. Dimensions below define a representative medium-flow remote unit for consistent product presentation; connection size, media area and change differential remain selectable for the actual pump flow and backpressure allowance.

핵심 재료	One deep-pleated HEPA-grade borosilicate microglass cartridge with synthetic drainage layers, perforated metal support cylinders and an FKM seal
패널 두께	45 mm nominal radial pleated-media pack depth for the representative single-cartridge configuration
유효 폭	180 mm nominal cylindrical housing diameter excluding pipe ports and pressure take-offs
최대 길이	520 mm nominal overall height including cover, drain and two-foot mounting base
강철 면면 두께	2.0 mm representative powder-coated steel cover, support saddle and mounting-foot thickness
코어 밀도	Approximately 120 kg/m³ representative effective bulk density for the finished pleated microglass media pack
열전도도 (Thermal Conductivity)	Approximately 0.040 W/(m·K) representative of dry low-density borosilicate microglass media near ambient temperature
표면 마무리	Deep-graphite impact-resistant housing finish with neutral zinc-plated or stainless port, clamp, drain and mounting hardware
접합 유형	One lower inlet and one upper outlet with removable pipe flanges, one circumferential cover clamp, two capped differential-pressure ports and one low-point drain
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

Connection sizes and flange standards matched to dry-pump exhaust flowAlternative HEPA element area for the allowable clean and loaded pressure dropHigher-temperature media and seal package for compatible warm gas serviceStainless-steel housing and base for corrosive or high-cleanliness locationsRemote differential-pressure gauge or transmitter connected to the two take-off portsManual or automatic condensate drain arrangement for the expected moisture loadInternal over-pressure relief setting coordinated with pump and exhaust-line limitsUpstream oil-mist coalescer or vapour-treatment stage selected for non-dry pump technologies

Planning a Vacuum Exhaust HEPA Filter specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.