Three-quarter overhead view of a complete Type 304 stainless steel AHU drain pan

클린룸 장비 예비 부품

AHU 배수 팬

A custom-sized Type 304 stainless steel condensate pan with a positively sloped floor and single drain connection for compatible AHU cooling-coil sections.

Type 304 Stainless Steel
Positively Sloped Floor
Single Drain Outlet
Welded Leak-Resistant Corners

견적 요청 제품 찾아보기

상품 소개

The AHU drain pan collects condensate below a chilled-water or direct-expansion cooling coil and directs it toward the drain connection. Its shallow Type 304 stainless steel body uses folded perimeter walls, continuously joined corners and a formed slope that converges at one low-point sump. Four external mounting ears provide defined attachment points without placing fastener penetrations inside the wetted floor. Replacement selection is based on the clear collection area, overall envelope, rim height, outlet location and connection size of the installed air-handler section.

주요 기능

The floor falls toward a localized low-point sump so condensate does not depend on a level flat sheet to reach the outlet.

Type 304 stainless steel provides a smooth corrosion-resistant wetted surface suited to routine AHU inspection and cleaning.

Folded walls and continuous corner welds keep the collection boundary clear of open seams within the condensate path.

A single side outlet and four external one-hole mounting ears create straightforward hydraulic and mechanical interfaces for replacement work.

고객 제품 관심사

Effective condensate removal requires the replacement pan to fit the coil section, remain accessible for cleaning and maintain a continuous fall to the connected drain line.

A flat or incorrectly oriented pan leaves standing water away from the drain opening.The floor geometry is formed toward a defined low-point sump and the outlet side is matched to the installed airflow-section layout.

An outlet at the wrong height, side or thread size cannot reconnect to the existing trap and drain pipe.Outlet diameter, centerline, thread form and left- or right-hand position are specified from the removed pan or equipment drawing.

Fastener holes or discontinuous corner seams inside the wetted area can create difficult-to-clean leakage paths.Mounting holes remain on external ears while the collection floor and perimeter corners use uninterrupted stainless surfaces and continuous welds.

A replacement that is too shallow or too narrow can miss coil carryover and overflow during peak dehumidification.Collection width, length, rim height and drain capacity are selected together for the actual coil face and available AHU cabinet space.

일반적인 응용 프로그램

Cleanroom AHU cooling-coil sectionsMake-up air unit condensate collectionDehumidification air-handler modulesReplacement drain trays for custom ventilation equipment

기술 매개변수

The following ranges describe common custom-fabricated Type 304 stainless steel drain pans for modular and replacement AHU coil sections.

핵심 재료	Type 304 stainless steel pan body, mounting ears and welded drain stub
패널 두께	40-100 mm nominal pan depth including the upturned perimeter rim
유효 폭	300-2000 mm nominal clear condensate collection width
최대 길이	Up to 3000 mm overall pan length for common sectional AHU replacements
강철 면면 두께	1.0-1.5 mm Type 304 stainless steel sheet for typical fabricated pans
코어 밀도	Approximately 7900 kg/m³ for Type 304 stainless steel
열전도도 (Thermal Conductivity)	Approximately 15 W/(m·K) for Type 304 stainless steel at 20 °C
표면 마무리	Smooth satin-brushed stainless surface with cleaned continuous corner welds
접합 유형	Folded perimeter walls with continuously welded corners and one welded male threaded drain stub
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

Custom length, width and rim heightLeft- or right-hand drain outletAlternative outlet diameter and threadOptional closed-cell external insulation

Planning a AHU Drain Pan specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.