Tiếng Anh
Tiếng Đức, tiếng Đức
Tiếng Ả Rập, tiếng Ả Rập
Tiếng Pháp, tiếng Pháp
Tiếng Indonesia (tiếng Việt)
Tiếng Nhật
Tiếng Hàn / tiếng Hàn
Tiếng Mã Lai
Tiếng Bồ Đào Nha, tiếng Bồ Đào Nha
Tiếng Nga, tiếng Nga
Tiếng Tây Ban Nha, tiếng Tây Ban Nha
Tiếng Thái (tiếng Thái)
Tiếng Thổ Nhĩ Kỳ, tiếng Thổ Nhĩ Kỳ
Tiếng Việt / tiếng ViệtHiện tại
Hệ thống tiện ích phòng sạch
Hệ thống thu hồi ngưng tụ hơi nước
A factory-assembled duplex electric return package that collects hot condensate in one vented stainless receiver and transfers it through two alternating low-NPSH pumps.
- One vented stainless receiver
- Two alternating electric pumps
- Pre-piped valves and level controls
Giới thiệu Sản phẩm
The Steam Condensate Recovery System is a skid-mounted electric return unit for collecting gravity-fed condensate and lifting it into a remote return header. The selected package has one horizontal atmospheric 304 stainless-steel receiver, two identical close-coupled centrifugal pumps mounted side by side beneath it, one pre-wired control enclosure and one externally visible level gauge. Separate suction branches feed the two pumps, while isolation and non-return valves protect each branch before both outlets join a common discharge manifold. The receiver also provides dedicated inlet, vent, overflow and drain connections. Float or magnetic level switches start, alternate and assist the pumps as the liquid level changes, while a high-level input supports local alarm and building-management monitoring. This identity is a condensate collection-and-lift package, not a flash vessel, pressurized pump trap, deaerator, boiler-feed dosing system or water-treatment skid.
Các tính năng chính
Two matched low-NPSH stainless centrifugal pumps in a duty-assist or duty-standby arrangement
Automatic lead-pump alternation to distribute running hours between the two pump trains
Independent pump suction isolation and discharge non-return valves for branch-level service
Common flanged discharge manifold for one field return-line connection
Visible receiver level gauge with separate control and high-level switching points
Pre-wired IP65 metal control enclosure with status lamps, selector controls and emergency stop
Rigid powder-coated carbon-steel skid frame with stainless-steel piping supports
Các mối quan tâm về sản phẩm của khách hàng
A condensate return package must accommodate hot inflow and changing load without cavitation, overflow, branch reverse flow or loss of pumping availability.
Hot condensate can flash inside a vented receiver and reduce the suction margin available to an electric pumpSize the receiver vent for the expected flash-steam load and select low-NPSH pumps with the required flooded suction at the maximum condensate temperature.
One pump may be unable to clear a peak return load or may be unavailable during maintenanceUse two equal pump trains with automatic lead alternation and assist or standby logic so the second pump can respond to a higher liquid level.
Reverse flow through an idle pump can cause unstable operation and complicate service isolationProvide a dedicated suction isolating valve and discharge non-return valve on each pump branch before the outlets combine.
An undersized discharge line or unaccounted static head can leave the receiver at high levelSelect the package from the actual condensate return rate and total discharge head, then size the common return line for the maximum combined pumping rate.
Các ứng dụng điển hình
Central condensate return from cleanroom air-handling steam coilsPharmaceutical utility and process-heating condensate collectionSterilizer, autoclave and jacketed-vessel utility condensate returnFood and beverage plant steam-heating networksMechanical-room condensate lift where gravity return cannot overcome the system head
Thông số kỹ thuật
The selected catalogue identity is a 200 L-class duplex electric condensate recovery skid with one horizontal atmospheric receiver and two fixed-speed pumps. The envelope and construction below describe this locked image configuration; pump duty, connection sizes, control voltage and vent capacity remain selectable from the hydraulic and flash-steam design conditions.
| Vật liệu lõi | 304 stainless-steel receiver, pump casings, impellers, suction and discharge pipework with a powder-coated carbon-steel structural skid |
|---|---|
| Độ dày bảng điều khiển | Receiver shell typically 3.0-4.8 mm for the selected 200 L-class atmospheric package |
| Chiều rộng hiệu quả | Approximately 650 mm skid depth for the selected duplex configuration |
| Chiều dài tối đa | Approximately 1500 mm overall skid length for the selected 200 L-class unit |
| Thép đối mặt với độ dày | Control-enclosure sheet and formed stainless guards typically 1.5-2.0 mm |
| Mật độ lõi | 304 stainless steel approximately 7900 kg/m³ |
| Độ dẫn nhiệt | 304 stainless steel approximately 15 W/(m·K) at 20°C |
| Kết thúc bề mặt | Neutral satin-finished and passivated stainless receiver and pipework with a black powder-coated structural skid |
| Loại khớp nối | PN16 flanged field inlet, vent, overflow and common discharge connections with bolted valve branches and welded skid pipework |
| Tùy chỉnh | Có sẵn dựa trên ứng dụng dự định và môi trường hoạt động. |
Các tùy chọn có sẵn
Duty-assist or duty-standby duplex pump logicAlternative receiver volume for the return profile and pump cycle ratePump selection for condensate temperature, flow and total delivery head304 stainless-steel or powder-coated carbon-steel frameAlternative flanged connection standards and nominal sizesVariable-speed pump control where a modulating return profile is requiredRemote BMS contacts for pump healthy, pump run and high-level alarmOutdoor enclosure, insulation and heat-tracing package for a defined climate
Planning a Steam Condensate Recovery System specification?
Gửi cho chúng tôi kích thước của bạn, điều kiện lắp đặt, mục tiêu hiệu suất và bề mặt yêu cầu hoàn thiện.
